Hi Team,
Is it possible to implement the iOS application to track the iBeacon Component after closing the application(Background processing).
Please provide any example...
Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
Hi Dev team,
I have my Thingy91 deployed and running. I wanted to know how could I locate the base station that my device is connected to. I have the information of MCC...
Hello, i'am trying to display data on my sensor Bme280 aka (temp, humidity and pression but the build is successful and the jlink is well connected the wiring is like below...
Hi,
I was using nRF Connect with all applications listed. But after installing nrfutil from git, the application all disappeared. I uninstalled nRF Connect and reinstall...
Hi, I'm attempting to use an nRF21540 to boost the range of a BLE Beacon, and I'm running into a lot of trouble getting the Eval/Dev Kit set up. First off, is there any documentation...
Is there an nRF Connect mesh sensor example. The light on/off example is great, but very simple. There is an nRF5-SDK-for-Mesh example. Are nRF5-SDK and nRF Connect compatible...
Hi to everyone,
I'm evaluating an application consisting of a bluetooth mesh where each node sends a status message to the others.
The area where the nodes will be deployed...
Hi,
We need to know the list of models (like health, configuration, lighting, sensor, generic on/off) in nCS sdk 1.7.0
can you please share inputs
thank you,
To update the Application, it is necessary to implement the update via CAN bus. Below is the hardware part, we use a CAN-SPI chip to access the bus.
We´ra using Microchip...
I would like to disable completely the 2.4Ghz radio after the 52840 has full soft device enabled and ble stack has been run.
This is after the full sequence of bluetooth...
Hi Devzone:
We put the radio test project on our custom battery powered board and encountered a problem.
When we disconnect the usb cable, the tone emitted by radio test...
Hello,
we developed the battery management system with a NRF52810.
Now the product is passing different certifications.
We need to provide info to the certification...
Hi
Trying to implement Full modem firmware update over serial port (USB) on nrf9160 in accordance with nrf\samples\nrf9160\fmfu_smp_svr in ncs version 1.5.1.
It seems...
Module: nRF52810
SDK: 14.2
Softdevice: S132 v5.1.0
Hi,
I modified the serial dfu bootloader exemple to use the SPI slave 0 instead of the UART to communicate between...
i try added Characteristic User Descriptor on nRF Connect BLE app
but on smartphone get Characteristic Extended Properties Descriptor
how can i fix this ?
Hi, I have some troubles with partitioning while using thingy91_nrf9160_ns. I have some FLASH overflow when compiling it with west using 1.7.0 library, while everything fits...
