Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi,
I am using ancs service to get some information of my iphone.
I use nRF51822 microcontroller and Nordic suggests to use the new SDK (5.2) for new microcontroller...
Hi,
I am using an NRF 51422 DK, SDK 12.3, and Soft Device S130. I am also a beginner to development with Nordic Products, and RSSI collection in general. I am using the...
SDK: 17.0.2
IDE: SES
nRF52832 module
Hi!
I have a nRF52832 based custom board operating on battery power. I assigned a variable to the non_init section in SES and...
Hey!
I have an isp1807 test board, which uses an nrf52840 chip, and an isp1p807 programmer (ISP130603E). Currently, my code is written using the nrf52 sdk v17. When I am...
Hi, I'm using nRF9160 as host and nRF52833 as a controller with NCS 1.5.0 SDK. On nRF52833 LPUART sample runs, I have added needed configurations for extended advertising...
Dear All,
I am working on interfacing BME680 with nRF52840-DK board. I got the output for Temperature, Pressure and Humidity but not getting the output for Gas resistance...
What should be considered for choosing a chipset? the followings are in my mind. Could you please tell me if I am correct and if I should consider anything else too.
1)...
Hi guys.
I flashed a uart-dfu Bootloader(SDK-location\nRF5_SDK_15.0.0_a53641a\nRF5_SDK_15.0.0_a53641a\examples\dfu\secure_bootloader\pca10056_uart), when the program run...
Can you, please, point me towards documentation and (if available) samples of mobile app that would allow me to commission and then interact with devices in RF52840-based...
Hi everyone,
So currently, i am working on a project relating to sending some message from one router to another. I found out that there is a function to create your own...
Hello everyone,
I've been struggling to use the Bluetooth UART example and the RTC2 module but so far I haven't succeeded.
Either I have Bluetooth, or RTC2, but not both...
Hello -
I have created a project with both a SoftDevice S132 and nRF Crypto libraries. All has gone well so far. I am now trying to implementing RNG, following the example...
The prototype I was working on has a nRF52832 on it and for some time it was working fine with the Segger Jlink base. However today I started to try to use the low power modes...
Hi,
I am using "TWI Sensor" example(SDK v17.0.2) as reference in our application. For multiple bytes transmission this is how I defined in "nrf_drv_twi_tx".
Here is...
I have searched Nordic and the web and have seen several instances of "can't uninit saadc successfully". Neither Nordic support nor I am aware of a single example of saadc...
