My goal is to control a RC toy drone (4-ch 2.4GHz) from a PC. I've seen some hacks (for example dzlsevilgeniuslair.blogspot.com.br/.../more-toy-quadcopter-hacking.html) using...
Hi Team,
Is it possible to implement the iOS application to track the iBeacon Component after closing the application(Background processing).
Please provide any example...
Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
hi.
As the manual says,It waits for an application event. and is called in the main while loop.
Does it mean that if I put some other routines carrying out polling function...
Hello, I am interested on nordic devices that support: 1) 802.15.4 (eg. Openthread) 2) secure storage for storing keys (e.g LWM2M credentials) 3) zephyr - rtos
I have seen...
Hi, we have a nRF9160 DK where we have uploaded the AT_CLIENT example on. Have tested the board and it works fine, able to send AT Commands and join to the network etc......
Hi,
I want to store scene when long press one button and recall scene when short press. I have done some changes but not able to achieve it, i am not sure if i should...
I was looking at this compatibility matrix, for SD and SDK.
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcomp_matrix_nrf52832%2FCOMP%2Fnrf52832%2Fic_rev_sdk_sd_comp_matrix...
Greetings!
we are using nrf5340dk to communicate with a Nucleo shield that has LIS2DW12 accelerometer on it (shield is X-nucleo-IKS01A3). We have a problem communicating...
Hello, I'm beginner for nRF52.
I saw examples about entering DFU by button and buttonless.
Is it also possible that changing the boot mode by a gpio pin which controlled...
Hello all, I'm working on ADC and data transmission.
Device do ADC first, and send those values.
Sampling frequency of ADC is ~80 kHz (sampling per 13 microseconds), and...
Hello,
We are using nrf52805 for our project. Facing some errors like "GATT ERROR" and GATT INSUF AUTHORIZATION and GATT CONN TIMEOUT ERROR" when I want to upgrade my application...
Hi,
We are developing our product based on nrf52382. In the scope of the certification testing of our end product, the test laboratory asks me if the Bluetooth low energy...
I am currently building a dynamic multiprotocol application (Thread+Bluetooth LE) with the nRF Connect SDK. For tweaking coexistence I would like to limit the length (=duration...
Hi,
In nwp-036 page 7,here is the AOD sketch map as below :
As fat as I am concerned, the Transmitter and Receiver should be reverse ?
Or there is something I misinterpreting...
Hi,
Background: I am looking at interfacing nRF21540 (FEM) with nRF52833 (Host) - hoping there's Zephyr support available for this(?)
Question: Product spec for nRF21540...
I'm trying to find the address of an attached twi sensor by using the twi_scanner. It worked on the default pins
but when I change the pins like this
It simply doesn...
Dear Nordic team.
We have to add new sensors using I2C protocol on our previous project.
Can i configure WDIO and SWDCLK pin to I2C pin?
If possible, i will reuse my...
