I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hi, I am using nRf9160 with last sdk (master branch) and Segger Embedded studio V4.52. When I compile and run any program everything works, but when I try to debug the program...
Hi community ! Imagine this configuration :
A -> B -> C
So A can't directly communicate with C. I send a message from A to C (And only C), so this one with be relayed...
Hi,
I am working on project which is based on nrf9160. I added the source files and user define header files . and also given the path of source file in CMake file. Build...
Is it possible to configure the Zephyr UART parameters like the hardware flow control dynamically at run time? We do that in an nRF52840 firmware with the nrfx libraries ...
Hi all:
Our usage scenario is to establish a connection and bonded between the NRF52840 peripheral device and the central device, and then restart the NRF52840 peripheral...
Hello,
I was working on a project SDK=16.0, SD=7.0.1, device=nRF52811.
After making a few changes to a working code which I compiled successfully many times before and...
Hello!
I am experienced in using mbedTLS on other platforms, and am in the process of porting my implementation of COSE (RFC 8512) to the Nordic SDK.
As a starting point...
HI NORDIC, I met a problem that Bootloader coulde jump to application, and the application crashed with freertos and softdevice SDK13.0. However the application could run...
After reprogramming with mfw_nrf9160_1.2.0 and nrf9160dk_asset_tracker_ltem_2020-04-29_bc7ade8b.hex
the nRF9160 fails to connect properly. LED3 blinks continually, LED4...
Hello,
currently i am using nRF52832 board with Nordic SDK 16.0.0 and softdevice version 7.0.1
i have separated DFU service and bootloader code. added dfu service in my...
Hello all,
I'm still learning C at this point of stage. What I ended up was following a tutorial online on simple BLE project controlling the on-board LED.
The tutorial...
This is a 2 part question concerning the LFCLK input levels as well as how to test the LFCLK frequency against the HFCLK frequency to make sure they are consistent.
In this...
I am currently working on a project using the MAX30102 Heart rate module. This sensor has red & ir led's. I connected the the max30102 sensor to the nrf52 DK as follows VDD...
Hi,
I'm looking at the BLE aggregator example, it uses a service called "ble_agg_cfg_service" .
1. It looks like this service is the same as NUS ?
2. I'd like to...
