Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Dear Support,
I have some troubles with the Evaluation Kit for nRF51822 :
I use the broad as a central role with S120_nrf51822_1.0.0_softdevice.hex and example...
Suppose a nRF9E5 transmitter is set for continuous transmission on a channel.
A nRF9E5 receiver listening on that channel:
finds carrier and sets CD
finds address...
Hello,
I am trying to 'recover nRF52840 dongle after accidental UICR erase' as described here I did modify my dongle as described here
Unfortunately I do not know how...
Hello,
NRF52840
SDK 15.3.0
SoftDevice: s140
OS: Ubuntu
IDE: SES
I am having difficulty getting consistency out of the RTT + NRF_LOG_INFO() print statement. It...
Hello,
I use the nRF5_SDK_for_Thread_and_Zigbee_v3.2.0_9fade31 with nrf52840-DK.
I'm looking for a way to get the transmit state after I sent a udp packet. I would like...
Hi,
we've been trying to reduce power consumption do I able to connect unused pins to GND directly?
Trace 1,2,3,4 do I able to connect to the GND?
Thanks, in advance...
Hi,
I am the first time programming with nordic and Segger. As I received the Thingy91 I just the getting started assistent to set up the toolchain.
This worked fine so...
I have the following setup, master (Nrf24L01) and several clients (Nrf52840), the clients listen, the master sends a message to one client and switches to listen. When the...
While most of nRF5 DSK modules have conditional compiling, such as
#if NRF_MODULE_ENABLED(BLE_DIS) the components/ble/ble_services/ble_dfu/*.c lack these macros. In my project...
Hello,
I use nRF5_SDK_15.3.0_59ac345 and ble_app_multiperipheral_pca10040_s132 .c code
In that code I integrate the capsense code it's work but after some time it's...
I'm want setting Secure_Bootloader.(IAR compiler, SDK 15.3version)
I followed the following guide but got stuck in Step B.
https://devzone.nordicsemi.com/nordic/nordic...
Hi All,
Can somebody point me to a Buttonless Secure Serial DFU Example from SDK16 or SDK15.3.0 for nRF52840-DK
I would use it with only Rx/Tx that is No Hardware Flow...
I want to read all data from a cluster is there a way to pass a wild card to
ZB_ZCL_GENERAL_ADD_ID_READ_ATTR_REQ(p_cmd, attr_id);
Or is there a smarter way to get the...
My nRF9160 DK is not able to connect to nRFCloud.com. I did the certificate update just in case to no avail. I have made sure to update the modem firmware to 1.01 and I used...
Hello, and thank you for making the nRFX components open-source on GitHub!
Now I realize that it's only been up for a day :smile: but most of the changes are reasonably...
