I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hi
In the last few months I posted a question about RTOS and softdevice and I need to read the answer again but I am struggling to find how to do that
Look forward to...
Mesh core is aware of the total length of DFU package. Why Application hasn't this data?
DFU packet DFU start has data field Firmware length (see here ) Mesh data structure...
Hi,
as my project moves forward I've switched to development of central board. In addition to space restrictions the board is promising to be a resource hog. A 2500+ mAh...
Hi,
I am using SDK13 and have noticed some critical issue with peer manager while bonding. The problem is that after performing dfu of my device (which was bonded with two...
Hello, I'm developing application starting from blinky example extracted from nRF5_SDK_15.3.0_59ac345 SDK. I see (using nRF Connect) that the connection result as "unencrypted...
This thread in zephyr community has left me confused about the features supported. lists.zephyrproject.org/.../31926113 .
Can you please confirm I can advertise and make...
when i try to debug with the segger develoment envrionment using a segger j link
i get the following log and a generic error
this is straightout of the box code no...
Hi ,
I am working on a NFC project which has below requirements , could you please help check if we have any existed example I can test ?
1. Support standarded ISO/IEC...
I'm looking for a nodified 'Wireless UART example" that I can use for a range test.
https://infocenter.nordicsemi.com/topic/com.nordic.infocenter.sdk5.v15.3.0/wireless_uart_15_4...
Hello,
I have problems using nrFgo Studio with my J-link programmer. The "nrf5x Programming" section is greyed out when the j-link is connected to the PC and the MCU....
I am working on a client to collect data from a continuous glucose monitor. I see that the CGM Service has been part of the SDK for some time. But there is no matching client...
Hello
I have nRF52840-DK and also a nRF52840 Dongle with me and i have installed SEGGER Embedded Studio with "nRF5_SDK_for_Thread_and_Zigbee_v3.0.0_d310e71" SDK downloaded...
Hi--
On dev kit PCA100056, SoftDevice s140, SDK 15.3, in project ble_app_uart_pca10056_s140, we are trying to operate the UART TX/RX characteristic with outgoing payloads...
