Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi,
I am using ancs service to get some information of my iphone.
I use nRF51822 microcontroller and Nordic suggests to use the new SDK (5.2) for new microcontroller...
Hello All,
I am using the example " iot_secure_dfu_bootloader_secure_dfu_s132_pca10040 " with the NRF52 DK board.
I have build and load the code in the board but it...
I want to know how to add custom field in the firmware package generated using nrfutil? I generate three firmwares but sometimes its error prone, I saw wrong firmware flashed...
I have used ble_app_uart example as the base project and have added FreeRTOS and SAADC example to it. And I get the following errors as attached in the image.I have added...
Hello,
I have merged nrfx_spim and ble_app_uart. I was testing the spi tx function as my application has specific timing requirements. I have experienced something that...
chip: nrf52832
sdk:nRF5_SDK_15.3.0_59ac345
my purpose: i want to store data to flash from ble_uart
demo: examples\ble_peripheral\ble_app_uart and examples\peripheral...
I followed strictly all steps of the nRF Connect SDK Getting Started Assistant. However, the code doesn't compile:
(...)
9> Compiling ‘reboot.c’ 1> In file included from...
Hi, i am working on a bluetooth application with the nRF52832. When i try to connect a Samsung Galaxy S8 (Android 8.0) via nRF Connect, i get a LMP TIMEOUT error after 40...
Launch, then select 'Launch Programmer, tool displays message "The app only supports nRF connect ^2.5.0 while your installed version is 3.0.0. It might not work as expected...
From what I could see the Asset_Tracker example works in LTE, not in NB-IoT. How can I test NB-IoT?
I would like to get some hint on what example to use and what to do to...
Hey all,
I'm a bit lost here... I developed a wireless sensor for a customer based on the nRF52840 and it works great. Now we're developing a small light weight gateway...
Hi everyone,
I'm trying to developp a MIDI USB class compliant device with the nrf52840 DK.
I'm beginner about USB developpement and I have only basics about MIDI class...
I am using SDK 15.3.0 working on nRF52832, on windows platform.
Our requirement is, we need to get the data from both nRF52832 and BLE Heart rate sensor at same time and...
I have developed a new board based around NRF91 module. Ten prototypes are produced and six of them work. Other four devices cannot connect to the LTE network. I am using...
Hi,
I'm using nrf_serial to configure and then read data from a GPS engine, but I am getting unrecoverable OVERRUN errors on start-up if the GPS device is sending data when...
Hello
the setup is a nrf52840, the sdk15.3, Softdevice s140, apps: open bootloader and blinky app
Is there a way that the DFU mode is always there, at the moment its only...
