We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
in Mesh SDK v2, simple on/off model example, client node doesn't act as a provisioner.
But I still want to combine provision & client in the same device.
Is that just...
Hi all,
I'm reading the ble_peripheral samples of the SDK. I know start a advertising with the function ble_advertising_start();
Now, i know a central address, then i want...
I'm using the PPI to generate a PWM signal on my nRF51822, and I've noticed that TIMER_SHORTS is never triggered unless the timer interrupt is also active. I had originally...
Greetings,
I believe I'm seeing the same issue as this DevZone ticket: https://devzone.nordicsemi.com/f/nordic-q-a/23903/gpio-behaviour-during-power-down-nrf52832/94059#94059...
Hi dear all !
the Question is very simply,
1. What the real RESET VECTOR (isr table) , ROM address for nRF52840 MCU ? I mean what happened each time after MCU CORE reset...
Using a nRF52832-DK and nrfconnect-2.0 on Win 10 everything works well.
But using that with Ubuntu 18.04 requires more installation documentation!
1. it seems, that the...
How many GPIOTE Tasks can I use at the same time. I want to drive six different pins with six different tasks which are connected to three events. Each event generates two...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
I have a peripheral (nrf52832) which is using a higher MTU (140 bytes). When I connect to it using the nRF Connect Android app, everything works. I can see the BLE_GAP_EVT_PHY_UPDATE_REQUEST...
Hi all,
I'm working with Nordic Thingy:52 (nRF6936 with nRF52832 inside).
Currently I'm working with original firmware (I mean, not modified firmware) version 2.1.0. But...
Hi,
I am debugging an SSD1306 OLED library, and in the datasheet, it does not explicitly mention support for repeated start bits. But using the nrf_drv_ API's with NRF_DRV_TWI_FLAG_TX_NO_STOP...
I would like to know what configurations are required to advertise long range.
Just changing the phy. returns error 0x07
I compared the ble_app_blinky and ble_app_att_mtu_throughput...
Hello,
I have done some consumption measurement but I have a strange behaviour while the nRF52840 is in the SYSTEM ON mode.
For the measurement, I send advertising packet...
Hi,
I have gone through the saadc example program supplied along with SDK15. But the issue is that, the example features a single channel ADC read. I tried to modify this...
Hi i am having simple doubt.I am using the Nrf51822 as peripheral device and running beacon example from SDK 12.0.0.I am using nrfconnect in my mobile(Central device) to scan...
