I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi
I am programming NRF-51 board using nrfgo studio, it was working fine previously but now it failed to detect the board showing error. I shared screenshot of nrfgo studio...
Hello everybody,
I have integrated the new S140-SD-v6 Stack 6.10 into the github.com/.../nrf52-ble-app-uart-long-range Example.
It built and compiled without any errors...
Hello,
I want to get the raw acceleration of the Thingy 52. however I can't understand the values I get from the raw acceleration. What is the unit used for raw acceleration...
I am using Nordic SDK 13.0.0 with PCA 10040 dev board.
I have configured the stack to use MAX_BLE_MTU_SIZE = 200
// Configure maximum size of ATT packet the SoftDevice...
Hi,
I encountered a weird behavior. i defined characteristics with specific read/write permission however all the characteristics are writable for some reason altough the...
Given this error handler function...
and this logging from it with the Segger attached...
how do I debug this?
I presume the info passed in is bogus and just points...
Hi All,
I'm currently using SDK12 for nRF52832. In my BLE peripheral project I store central address who engaged my device to listen for ANCS notifications. This address...
Dear Nordic Community,
I am using the the nrf51 dev kit to try and program a custom board (nrf51822) connected to it via the the Debug Out connector. This setup has worked...
Hi,
I'm testing nRF52832 central data rate.
My SDK version is 14.0.0 and softdevice is 5.0.0.
I want to send 200byte from nRF52832 peripheral to nRF52832 central in one...
Hi,
I'm using NRF52840 with Softdevice and SDK v15. I would like to use an external 32.768kHz crystal.
If I understand correctly this is consistent with the eval board...
Would you please provide an example of using PA/LNA with nRF52840 (Softdevice S140) on SDK 15.0 or higher?
Unfortunately, I could't manage the code you've provided for the...
Hi With regards to iOS and Android versions of the 'nRF Mesh' applications .. (1) How can I tell if both apps are 'synced' to the same level of functionality/user interface...
Hi,
I want to test UART peripheral on nrf52840 by running example in path examples\peripheral\uart as it is.
Connection setup is:
nRF power source USB
nRF USB port...
Hi all
Previously, I used the nRF52832 with the interrupt-driven UART at 1Mbaud. But due to SoftDevice interrupts that blocked the UART-RX-IRQ for more than 6 bytes, I tried...
