Hi All,
i would like to know about
1) what is channel in nrf51288?
2) is there any mathematical relationship between channel no and pin no as in ble_app_hrs
example channel...
Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I can run the SAADC example and read the analog inputs fine, now I've modified the code to simply read the adc with the blocking nrf_drv_saadc_sample_convert call
All I...
Dear All,
while testing an own nRF52832-based PCB and an nRF5840 PDK for current consumption, I compiled and flashed the code below to both devices. Since then I am not...
Hello All,
I don't find any example of Dynamic Multiprotocol of ESB and BLE.
The current multiprotocol example in Nordic’s nRF5 SDK is a switching solution for multiprotocol...
Hello,
Here is a summary of my main transmission protocol:
The (unique) client contact one of the many servers to get the value of a particular server's state.
In the...
hellow nordic.
i use sdk14.2 ,but pstorage_update return NRF_ERROR_NO_MEM.
i use NRF_SDH_SOC_OBSERVER(m_soc_evt_observer, 0, sys_evt_dispatch, NULL) to creat sys_evt_dispatch...
I have a couple of "cannot-be-resolved" issue with Eclipse.
Issue 1:
Sometime when I set up a project in Eclipse, it runs into an issue where types like uint32_t or...
Hi,
I'm trying to send sensor data via BLE to Processing. If someone has already done it, could you post your code or help me explaining how to approach the problem?
I...
Our Nrf51822 will disconnect the connection with timeout reason when it is sending a large amount of data (about 20-70 KB) to our central device which is TI cc2540 . This...
Hi Nordic.
I have questions about preserving device unique information such as device id and so on. (The information will be written in factory)
I know the best way is...
I am trying to add I2C/TWI bus to nrf51822 device. I have used the SDK example code (12.3.0) and keep getting the following errors:
sdk/drivers/nrf_twim.h:69:38: error:...
Hi, Is it possible to make the same nRF52832 device to function as a master for some interval and then switch it to slave?? i.e, Does Nordic have a single SoftDevice capable...
Hello, the current QIAA package is rather demanding on the manufacutring and significantly increases our cost, are there any alternatives? I failed to find any in the datasheet...
Hi !
My goal is to create a large mesh network (over 100 nodes).
I plan to have 3 kind of nodes : a client (connected to a PC), several server relay nodes (not on battery...
Hello,
I have got a question about gpio current protection in nRF52 - I have checked forum but I haven't found answer on this specific question. In nRF52 specification I...
