Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
What is the typical expected receiver sensitivity when performing BER test (1Msps, 16 byte packets) of the radio module ? The spec refers to 2 values: -93 and -96 dBm (p.231...
Hello,
We are considering merging the Eddystone and iBeacon features together, packet types toggling at each interval tick, then we assumed that we should take the Eddystone...
My device is sending a beacon under DEBUG, but not under RUN.
The issue started when I converted the scan_and_forward example to use a 16-bit device address.
It steps...
Dear Sir or Madam,
I'm using a dev kit with the nRF52832 to realize a project in school. So my work contains two wearables and both include the nRF52832. Now I want to communicate...
Hello,
is it somehow possible to calculate the distance of a BLE enabled and advertising periodially cell phone to a turnstyle gate.
There are for example 10 turnstyle...
Hello,
I'm trying to update from Mesh SDK 1.0.0 to 1.0.1, I've followed http://infocenter.nordicsemi.com/topic/com.nordic.infocenter.meshsdk.v1.0.1/md_doc_getting_started_how_to_nordicSDK...
Hi all,
I would like someone give me a suggestion about timers.
in my current approvement I am using an RTC timer with 32k crystal to control my sleep times it is power...
Hi there,
I have an nRFready Smart Remote 3 in front of me to evaluate for development of an upcoming product. I've had a look around the forums and documentation, but...
I’m currently making some measurements with a power analyzer on both, our own hardware design with the nRF52840 (Samples B) and the nRF52840 Preview Dev Kit.
I took the...
Hello Community,
this is my first question, since I could not find any clue on the internet and here on the devzone.
Problem:
I need to read/write a value to a GATT...
Hi,
I compiled (using ARM GNU) and run the USB CDC ACM example found on SDK_14_0_0. I have windows 10.
Windows 10 do not reckognize it as a CDC device and instead I...
hi,
I am developing with nRF 52832 on my own board. the code worked fine until I added the UART_init() function. my source code outputs an error message.
i reinstalled...
Hello,
How reset device from code to take effect of enabling access port protection? NVIC_SystemReset() doesn't work. I can read flash using j-link.
Device: nRF52832
Hi all
We are experiencing high current draws that lead to 51822 chip failure under some circumstances. By looking at this thread
https://devzone.nordicsemi.com/f/nordic...
