I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Is this chip for sale yet? I see dev. kits, but still 28 week lead time everywhere. We were talking about adding it to a product, but the owner is shooting me down because...
Hello NORDIC community,
I am performing a BLE throughput speed test via an example of streaming a buffer of 2500 bytes per second: This says a sending frequency of 19 Kbps...
i used SoftDevice s332,and download the example:\examples\multiprotocol\ble_ant_app_hrm
i find that using android device can connect pca10040 ble well,but use ipad or iphone...
Hi
We are working on a product using NRF-51822 chip. I am new to Nordic SDK and want to know how to use fstorage to save data into flash. Following is code. Sometimes data...
Hi,
I would like to build a project with functions below.
Support BLE uart service
Support CLI with uart interface for the communication with terminal, like TeraTerm...
Hi All, I am building a wireless MIDI controller using the BLE nano v2.0 from RedBearLab.
MIDI is a protocol to control software musical instrument, therefore latency needs...
Hello everyone,
I try to modify SDK 14.2.0 S132 ble_app_template example with Segger Embedded Studio, but I got an error about uart. All uart functions appear to be "undefined...
It seems that the version of the soft device used in the mesh sdk does not match the version of soft device SDK that I can download, and the version used in the mesh SDK has...
Hi,
I am trying to run the examples for the pc_ble_driver_py and I get some issues.
advertising.py says "board not found"
heart_rate_collector.py gives a calledProcessError...
Hi folks,
I want to do a project from scratch using the Segger compiler. Where can I find relevant documents with it. How can I make changes on the Blinky project? For...
Hello,
I have two version of Python 3.6 installed: 32 and 64 bit (Windows 10)
Recently i installed nRF5x command line tools (9.7.2) and pynrfjprog 9.7.1
For Python...
In zephyr many PPI has been employed in radio, and other PPI from 20 to 31 is pre-programmed channels and can not use by application. Do you have any plan for optimize this...
hello,
I have one problem to distinguish the following 2 functions :
ble_srv_is_notification_enabled and ble_srv_is_indication_enabled
in on_write function,
the two...
Hi Nordic
I saw the Dfu example.
BLE Secure DFU Bootloader and Buttonless DFU Template Application. I have two questions here. The boot loader and app distinguish a ram...
