Hi Team,
Is it possible to implement the iOS application to track the iBeacon Component after closing the application(Background processing).
Please provide any example...
Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
Hello,
What would we expect the INFO.VARIANT FICR register's value to be with, for example, an nRF52811-CAAA-R7 vs. an nRF52811-CAAA-R7-B?
Right now I am seeing "AAA0...
Hi we are working on a matter project using ncs v2.6.0
Currently we are running out of RAM memory and that´s why we have moved to minimal logging by enabling
Now we...
I want to use 5" inch display for my project as nrf52840 is not able to handle that so I want to FT8xx EVE for the screen functioning? so did anyone has try this or any leads...
Dear support,
I performed a 48 hours- 20°C profiling of my 110mAh battery and managed to get my profile (really appreciate your nPM PowerUP tool. Helping a lot for development...
Hi.
I am working on a custom nRF52810 board (SDK 2.7.0).
When connecting LIS2DH12 via SPI in the .dts file, I see an error -->
.dts code -->
prj.conf -->
Please...
I try to capture the broadcast packets from the broadcast_audio_source application to investigate the BASE (which holds the configuration of BIGs, subgroups and streams)....
Hi DevZone Team,
I hope this message finds you well. I am reaching out to seek your assistance regarding the HID mouse implementation we are working on using the Nordic...
The question concerns using the nrf fuel gauge library for a setup with an nPM1300 PMIC and an NRF52840, implemented using the nRF5_SDK_17.1.0. Is it possible?
Even with the LTK key entered, wireshark cannot decode Bluetooth packets between two paired connected devices I followed this course exactly,but it failed to live up to expectations...
NRFX_TWIS_EVT_GENERAL_ERROR
I am thinking of implementing TWI slave functionality in the nRF52840.
The event handler is written as follows.
Read operations from...
I am thinking of using nRF52832 as both transmitter and receiver, and creating a firmware where the transmitter adds the acquired data to the Manufacturer Specific Data of...
Hi Nordic：
SDK version: NCS_V2.7.0
sample： peripheral_uart
config：
Compile error without any changes：
May I ask how to solve this problem？
best regards！
jermi...
Hello,
I get the error message in red when pressing Connect below:
The certificate is downloaded as instructed in the devacademy 4.2.
server_certificate.crt: ...
Hi,
I recently purchased a Thingy91, and here's what I’ve done so far:
Built the firmware
Registered the SIM and device on the cloud platform
Built the Asset Tracker...
