Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
We are developing a sleepy end device using the nRF52840, using light switch sample . The end device is connected to a Zigbee coordinator, also based on the nRF52840.When...
We are using a 5340 with a Skyworks 66112 FEM. Below is our hci_ipc.overlay file.
We are setting CONFIG_BT_CTLR_TX_PWR_ANTENNA =20. When we measure the output of the FEM...
I'd like to use playback feature of PWM. There is NRFX function for that: nrfx_pwm_complex_playback(). This function, like other NRFX drivers, needs appropriate instance structure...
My Win10 app - needs to connect to an NRF52 that is using the "NuS" Service - and I can't use the WinRT or dotNET.
In this post: https://devzone.nordicsemi.com/f/nordic...
Hello,
Thank you for reading my question. My company and I have developed a BLE device for use with windows computers based on the nrf52810. The device pairs with windows...
I'm building my zephyr project for nRF5340, using west.
However, each time I change my code and re-build to try it, my PC (which is pretty recent) takes around 40-50s just...
Hey.
I have a problem where the task watchdog times out immediately.
I have taken the samples/basic/task_wdt sample and modified it a bit to simulate what I have in...
The environment setup I'm using is VsCode with the NRF extension. I'm using SDK v2.6.1. When flashing bootloader firmware to my device I get this output on my vs code terminal...
minimal_log % west flash -- west flash: rebuilding [0/4] Performing build step for 'mcuboot_subimage' ninja: no work to do. -- west flash: using runner nrfjprog Using board...
We have fairly regularly observed that the reset reason register gives two reasons for reset: software request and watchdog.
Is it plausible that these bits are genuinely...
Hi,
I am trying to communicate with nPM1300 PMIC board using NRF5340DK. I have made the connections and set up the overlay file as recommended. The I2C write (i2c_write_dt...
I am currently developing software of the nrf9160 and am having trouble with a firmware upgrade. The firmware data is received via UART. All of the functions work as expected...
Hello all,
I am working on a ble application on zephyr. I need to send a notification on a specific characteristic.
If I call bt_gatt_notify from where I want to send...
We're currently using a virtual operator as carrier, so our device is roaming in Finland. It seems that Elisa (24405) is the preferred network, but the data plan is restricted...
