Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I've recently began experimenting with the HID service and connecting to iOS devices in order to achieve lower connection intervals with Apple products (as described in their...
I have successfully compiled my project using `west build` and now I am trying to load it onto my nrf5340 board I recently purchased. Here's what I'm doing:
- From the same...
Hi,
I would like to test some environments. Therefore - I would like to use an example from SDK 17.0.2, which allows me to connect to a PC via NFC, as a peripheral, receive...
I'am working on nRF52840-DK and nRF9160-DK.
i'd like to add an interrupt pin for a SPIM device. (eg. in the following spi_dev: )
&spi3 {
compatible = "nordic,nrf-spim...
Dear nordic team,
i want to take log from dfu example i tried using rtt veiwer but it doesnt work.im using sdk version 17.0.2 and soft device 7.2.0 and nrf52840 DK
in...
Hello ,
I am using nRF52832 , sdk 16version. I want to set the BLE connection interval via BLE command using application. How to do that? I tried to assign the variable...
Hi,
I’m using the nRF SDK 1.6.0 and trying to build the “ memfault ” sample for nRF9160 using the
“ nrf9160dk_nrf9160ns ” board. The sample location is:
C:\Users\username...
Hello, after I make the connection to the nrf device with the phone, I found there is only a "Forget This Device" option on its setting page. So is there a method such as...
Hi Nordic,
The bluetooth qualification needs the information of nF5340's value n for Intermodulation test but hard hard to find in any document.
Please help us out, thank...
Hello,
It appears that when the project is generated it is expecting a "../common" directory?
CMake Error at /opt/nordic/ncs/v1.7.0/zephyr/cmake/kconfig.cmake:209 (message...
Dear Sirs,
after "few" hours of testing, I noticed that nRF9160-DK loaded with SLM v.1.6.1 is not working the same after awakened up from sleep (#SLEEP=1) or even from idle...
Hi everybody,
I have developed a project where a central device with multilink, connected to the maximum peripheral as much as is possible (in my case 4 devices more). ...
Hello,
I'm trying to figure out how to get A-GPS data via a GSM modem in places where LTE-M is not availalble.
Does the SUPL library support this, if I populate supl_client_ctx...
Hello all,
I just found out that the nRF Connect extension for VSCode has been release, which is great news. Good job Nordic Team! I have followed the steps described in...
Hi, dear Nordic.
I'm using BC805M Module which uses nRF52805 SoC. What's the max sink/source current for individual pin OR total chip, please? Where could I find relative...
Hi,
Im using nrf9160 based custom board, nrf sdk 1.5.1.
I want to get the time from NTP servers, for that i connected to CATM1 n/w, connected to NTP server using UDP Protocol...
