Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Hi,
Would like to understand when will be the chip select pin be asserted and de-asserted when reading/writing a QSPI external flash?
What will enabling QSPI by setting...
Hello and to whom it may concern
I am currently using nRF51422_QFN48
with laser marking on the IC body
N51422QFAAF01616CS
i am using nRF desktop connect and try to...
Hello,
I'm having this problem with this nRF24L01+ connected to an ESP8266 (ESP12-E on BOB), and I'm using NodeMCU 2.2.1. The nRF24L01+ module I'm using is a small board...
Hello everyone,
i have a problem reading data from MAX30101 sensor FIFO. I set up the sensor and enable all 3 LEDS (Red, IR, Green), but when I read the data from the FIFO...
I'm using nRF Connect v1.5.0, Zephyr, and Segger Embedded Studio (SES) to develop an application I'm testing on nRF5340-DK.
I have a project that compiles and runs. But...
Due to the recent semiconductor global shortage, we are changing the chip on our device currently on the market from the nRF52832 chip to the newer nRF52833. I am in charge...
RNG interrupt handler is not called.
Using nrfx_rng library to generate random numbers.
VALRDY event is generated but interrupt handler nrfx_rng_irq_handler in library...
I have looked at the UART example provided in the NRF52 SDK. The example uses the UART in blocking mode. I need to create a version that is non-blocking, and only reads the...
Hello Nordic,
I was looking at multiprotocol support from nRF Connect SDK by following this link: https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/ug_multiprotocol_support...
Hi
Trying to install and operate the Sniffer based on nRF52840 USB Dongle
Having the nRF Connect for Desktop installed and burned the Dongle in accordance with the instructions...
Sorry I have to see how the ssp of ublox work.(nina 410)
II have to send a packet over the serial every 50mS.The packet len is 100byte.
I see that some time the received...
Hey DZ,
I'm having some trouble with the download_client. It's not playing nice with the HTTP server I'm using. On the last chunk of data, the nRF91 is issuing a Content...
Hello everybody.
I am developing a firmware which allows us to send data bidirectional between Central and Peripheral. On the one side we have a nrf51-DK and on the other...
