Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Hi
I'm working on an application that utilizes CODED_PHY.
I'm working on top of ble_app_blinky examples (central and peripheral).
I've seen this post on DevZone:
https...
Hi forum,
I am working on nrf52832, using sdk 15.0.0. I am working on Ble_beacon using sdk sample code.
In the Sdk_config.h file default enable uart0. Why this need to...
I am trying to get the nRF BLE Sniffer v3.1.0 working on my Mac running Bg Sur using a nRF52840 dongle. I have followed all the instructions listed in the sniffer document...
mergehex does work with file paths with "..\" in them. Here's my folder structure:
project root
Firmware
Application
Bootloader
SDK_Libraries
nRF5_SDK_17_0_2 ...
We are using nrfSDK1702. We have been trying to lower the current from a beacon. The beacon is active every 10s, then go back to sleep. The current consumption stays around...
Hi all! In my example after (i guess) 3 mins with out BLE connection the system goes to sleep mode. ¿Is there any way to avoid this ? Thank you so much!
Hi,
I'm connecting with my cell-phone for the field-try test.
I want to know the modulation type when it only use the connection type??
And what the modulation type...
Hey at all,
today I wanted to set up 7 new Thingy:91 devices. All thingys are 1.4.0 // 2020.23.
So I started with updating modem FW (mfwnrf9160123) and flashing thingy91_ltem_2021...
I've modified an example project.
How do I go about exporting it, so that I can share it with other devs and they can then flash the same program onto their Development...
hello,
i am working on nrf52 dk board .NUS sdk 16
I'd like to know the start/end characteristic handle values for each service. Is the 32-bit service handle encoded as...
I have inserted the groups cluster at an endpoint. Yet, and eventhough a group seems to be additioned to the device (the device responds with 0 to the add group command from...
hi:
I need help with a problem.
Error in merge file for 52810.
use sdk:nRF5_SDK_17.0.2_d674dde
bootloader:secure_bootloader
app:ble_app_buttonless_dfu
app:FLASH_START...
Dear Nodic friends,
We use nrf52833 to design a BLE control box with USB DFU function.
During USB DFU, DFU Trigger Library will reset nrf52833, so we should connect a...
Hi
I'm trying the light lightness example, I'm using nRF Mesh Android app for provisioning. I've 2 nrf52840 DK's. One is for client and other one for server. Both of them...
Hi,
I am trying to implement BLE on nRF52840 using Zephyr APIs. I am wondering if anyone can elaborate how to use bt_gatt_write() and bt_gatt_read(). As of now, I am able...
