Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
Hi , I am compiling the bmdware project (in IAR embedded workbench 8.32.2) and I have errors (particularly Errors while linking assembler, shown below).
I have modified...
Hello,
I am using Segger Embedded Studio version 4.52b and when creating a new project, it automatically creates a segger link script file and sets the linker to 'Segger...
Earlier with SDK 13 in custom advertisement I was able to send 30 bytes under unknown characteristics tab in Nrf connect APP but in SDK 15 I am not. Because the firmware or...
Hi everyone,
I started working on the nRF9160 with a Thingy91. I installed nRF Connect SDK v1.2.0 and i was able to try some sample like GPS or AT_client. However I would...
Hi ,
SDK : 16.0.0.,Mesh V4.0 ,PCA10040
My project requirement is : I need to use 2 dev kits one as a server and one as a client communicating each other on BLE Mesh
...
Hello, I'm setting up a mesh network with low consumption sensors and I'm using the Low power node example. I'm having trouble increasing the number of devices supported by...
Hello,
How can I directly read out the POFCON register value on the Watch Window while debugging?
Where is it actually located in the library(sdk 14.2) source code?...
How can i know how much time the microcontroller spends in the timer_event_handler() function? I am fear that i have written down to much code into that function. Regards
Hello,
I have the following statement in flash_placement.xml:
<ProgramSection alignment="4" keep="Yes" load="Yes" name=".nrf_queue" inputsections="*(.nrf_queue*)" address_symbol...
Hello.
I have two nRF52832 (central and peripheral). Connect the central and peripheral and call sd_ble_gap_rssi_get() on the central to get the RSSI and channel. The attached...
Hello there!
At this stage of the product development cycle, we would like to be able just to take simple reading from ADP536x module (to read either battery percentage...
Hey all,
For new minor revisions (1.X.0), will they eventually be supported by telecom's that are currently running with lesser versions? For instance, the current modem...
Hi,
I am using nrf52832 with icm20948 (I2C) on custom board and I am using icm20948 for angle measurement. For custom application I added some features i.e, before reading...
