Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Hello,
Currently I have implemented a UART callback using the CONFIG_UART_ASYNC_API setting as follows:
However, all data that I receive is appended constantly, until...
Hi, I want to measure the data transfer speed of BLE. I use the nRF52840 DK with the ble_app_uart example
I created a dummy string of 20 bytes (default length of one packet...
I have a shipping product with S132 2.0.1 with multiple problems with the LFRC clock.
There are seemingly at least 4 errata that apply (77, 132, 146, 192).
Are there...
Hello, I'm trying to compile the LIBUARTE example from SDK 16 but im getting undefined reference errors, this is what I've done so far:
in sdk_config.h defined , (I've...
Hi, I am really confused about the Nordic SDK and way of doing things... I have seen so much conflicting documentation.
I am using SDK_for_Thread_and_Zigbee_v4.1.0 (currently...
my project is to send pressure data from one device to four other devices, it is medical field, previously i worked in nordic openthread udp protocol using nrf52840 for mesh...
Hello
Created in SDK v17 and simple_timer example. I made a simple code to control the LED using a timer. Every 500 milliseconds, the LED turns on sequentially. LED ON and...
I recently got the nRF52-DK for using as BLE Relay evaluation.
I have downloaded following and installed to run the code
- Segger Embedded Studio (v5.1)
- nRF5_SDK_17...
https://infocenter.nordicsemi.com/topic/nwp_034/WP/nwp_034/nwp_034_intro.html?cp=16_2
download PDF link not working. Perhaps replaced with other white paper(s)?
Thank...
Hello!
I have the following component in my device tree:
I would like to retrieve the PWM device and the associated pin number (pwm1 and 0x14). I tried:
Which...
Hello,
I am trying to develop a firmware to read pulse oximetry and heart rate data from this Sparkfun module (SEN-15219): https://www.sparkfun.com/products/15219
The...
Hi,
We mainly need AWS_Jobs, FOTA, Low Power, GPS, ADC, GPIO, certificate updates and whatever is related.
Currently we working on a project that uses:
- nRF9160 ...
Hi All:
I am trying to develop a project based on Heart Rate example. SDK version is 17.0, the receiver software is based Android-nRF-Toolbox.
Now, I can transfer ADC...
