Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Hello!
Now I have two devices about nrf52832 .One is central and another is peripheral. So I want to transfer the peripheral mac address to the central via nfc.
I do...
This is the config fun followed。
one sample every 125ns,one ant get 12us =96 samples.
and first 2+32 samples is ignored。
*******************************************...
I've already tried to set some zephyr configs, but n51822 to run as peripheral it nedds at least ~20KB
Have anyone got success or all the nrf51822 QFAA H2 will really never...
development environment： SDK 14.2 , NRF52840 as central and NRF52832 as periph for Bonding: Passkey Entry, Central displays, and the error occur on nrf52840.
I want to know...
Hi all! I am currently using an nrf52840, mesh sdk v3.20 and sdk v15.30
I have the following scenario which I am trying to solve:
I am receiving a new GAP name for each...
In an earlier thread ,
[quote userid="17188" url="~/f/nordic-q-a/33649/j-link-the-firmware-of-the-connected-j-link-does-not-support-the-following-memory-access-read-0x02000004...
I'm using the nus_c service with multiple central connections. Obviously, I need the connection handle in my event handler - ble_nus_c_evt_handler(ble_nus_c_t* p_ble_nus_c...
Our product use two NRF24L01+. One is for transmitting and another is for receiving. They communicate by 250Kbit/s. It is pre-production.
Now, we want use nrf52810 to instead...
I just trying log via Segger RTT viewer, followed the the same procedure as that of serial_lte_modem sample in my new project and could not see logs showing in the viewer...
I am working with nRF52 DK, SES4.30 and SDK 15.3 with SD 132.
This error just started occurring once I set up app_timers. My code for setting up my timers is below:
...
Hello,
I ordered a nRF5340-PDK board and i'm trying to get it to work.
When flashing the Heart Rate hex file I couldn't find the device (i pushed the reset button)....
I am using SDK 15.3, SES 4.30 and softdevice 132 with the ble_app_uart_c as the core functionality for my system.
I've read many dev support threads about this issue and...
hi... I am working on nRF52832 . nRF52832 ,RX TX is connected to the esp8266 of tx,rx . i want to send the data from nRF52832 TO ESP8266 via uart . which function can i use...
I'm running the ble_peripheral\ble_app_uart example on my nrf52832, it works great.
However, in main.c there is this line:
#define DEVICE_NAME "Nordic_UART" /**< Name...
