Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hello,
I program the nrf51 in C++ using GCC and Eclipse as IDE (this question is not related to the C++ toolchain).
I was wondering if it is possible to add the extern...
Hello!
I bought NFR52 DK preview board. As microcontroller it works well. But when I try BLE examples, they do not work. I installed SoftDevice S132, downloaded ble_app_uart_s132_pca10036...
Hello!
I want to add the battery services in my nRF51822 project for getting the message of battery. Is there need battery-powered?
But,I am sorry to see that the led which...
hi everybody,
I'm working in a project, I need to establish a connection between a beacon & the mobile phone, I want to prevent any other masters of connection to my beacon...
I am having an issue with running the initial blinky example that came with the nRF51 PCA10028 SDK in the Eclipse IDE . I will include screenshots of the issue. I believe...
Hi new to Bluetooth, but familiar with Radios and embedded devices
I have 2 devices that only connect to each other.
in the interest of extreme battery conservation I...
I am using a BLE UART friend module and I am trying to set the GAPIntervals parameters. I realised that when I set my max conn interval parameter above 2000ms, the device...
I am planning to use the nRF51822 and the s130 soft device to manage data coming back bluetooth sensor nodes. It is likely that there will be more than 8 peripherals, although...
The SoftwareSerial library allows GPIO pins to be used as TTL serial pins by bit banging.
The nRF5 suffers from the same problem that the Arduinos have. 1 UART.
Does...
Hello guys
I tried to start TWI bus and got a lot of questions. (NRF51 1422 AC)
I added necessary libraries, could You tell me what more i need to include in my code ...
Hi , We are using NRF52832 for our product .I have a small doubt in using GPIO . Can we use PORT and PIN events simultaneously at a time .
I need to configure some pins...
Hi,
I have three beacons in my setup:
One listening (R1) and two transmitting (T2, T3). T2 and T3 transmit packets with same length.
Say, T2 has started transmission...
Hello,
My system is one device with multiple host, these host will connected to the device on irregular basis.
The host action are listed below:
scan->connect->write data...
hi, i'm going to do some project with nrf51822 and SDK 6.0.0.
i just made up ble connection between phone and the chip.
and i want to send data some fixed time periods...
