Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi,
I would like to connect my msp430f1611 with NRF8001 bluetooth module and send data with an SPI communication. I found an interesting guide here with the main part of...
Can someone from Nordic (or anyone who knows) comment on what happens when scanning and advertising simultaneously with S130. For example:
Scan Interval 100ms
Scan Window...
What are the conditions that can cause
sd_ant_burst_handler_request(Channel_0, 8, tx_buffer, BURST_SEGMENT_END) to return NRF_ANT_ERROR_TRANSFER_SEQUENCE_NUMBER_ERROR? If...
Hello,
I manage to work with new S310 V2.
I use S310 for hrm only. Saying so also not for DFU service.
I have own proprietary method for transfering application images...
Hi,
I developed application whitch is using S130 soft device. On central side to manage devices, i've used device manager from sdk 6.1.0. It works fine.
But now i need...
I tried to upload application through BLE DFU in MCP. The DFU Android app works fine. However, it always failed in MCP.
SDK 6.1.0
SoftDevice 7.1.0
MCP 3.7.1.8567...
Hi,
I have following use case. The write operation on one of the characteristics triggers some UART job which takes about 1 / 1.5 seconds to complete. After the completion...
Hello,
I try to use the S310 V2 but got stuck into problems.
in order to start the application from bootloader in the S310 V1 I did succesfully :
void (*application...
Hi,
I have problem on compiling bootloader example which is located at
\Nordic\nrf51822\Board\nrf6310\device_firmware_updates\bootloader
When I try to compile the...
Hi,
Some questions in example ble_app_hids_keyboard/main.c
Why set the adv_params.timeout to zero in BLE_DIRECT_ADV (Line 779) ?
That will cause no BLE_GAP_EVT_TIMEOUT...
I just got a nRF51 and am having trouble getting started with it. I created a very simple program using the mbed compiler and produced a hex file which I now wish to flash...
Hello,
I see that the make files that have been included have provision to remove dead code from the projects to reduce code food print. This is accomplished using the...
HI folks,
I have checked the current consumption while connected on an average to be 325uA (with uC taking 4.5uA) so this mean almost 320uA being consumed by the nrf8001...
I have a general question about the RF frequency tolerance of Nordic devices in general. Is the following calculation correct?
Crystal spec = 16MHz, +/-50ppm tolerance...
