Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Hello I am trying to build the Zephyr mesh distributor sample on the nRF 52840 dongle It builds and runs just find on the nRF52840 DK But when I try to build for the dongle...
I made a custom board And I am running the segger example ble_app_blinky_pca10056_s140 But Even if I run log_init();, it returns error code 5 And even if I run timers_init...
Hi,
I have updated the device application firmware from nRF Connect SDK v2.6.1 to v2.7.0.
The firmware was working fine in v2.6.1 without issue. But the same firmware...
mcu: nrf5340
board: nrf5340dk_nrf5340_cpuapp
sdk: v2.6.1
When I configure CONFIG_BOARD_ENABLE_CPUNET to enable cpunet, there isn't an issue. However, when I configure...
Hi, I have been trying to use my esp host mcu with nrf5340dk as a controller.I am using the hci_uart application with CONFIG_BT_LL_ACS_NRF53 =y to include le audio support...
Hi All
I am experiencing an issue with the nRF DFU app (v2.7.0) on devices running both Android 11 and Android 14. The issue occurs when I attempt to perform a DFU update...
Hello,
I want to run mass storage on my custom board with the nRF52833 and W25Q512JVEIQ. I have reviewed the mass storage sample (ncs\v2.7.0\zephyr\samples\subsys\usb\mass...
Hello,
I have a custom board with an nRF52833 and a W25Q512JVEIQ, which communicate over SPI (not QSPI). I successfully accessed the W25Q512JVEIQ (executed my own read and...
Hi, I am using nRF52832 module BL652. I want to measure the battery voltages of a 9V battery. What are the best possible resistors value to measure voltage of such battery...
Hello, We have a custom PCB with both the nRF9160 and nRF52832. Currently, the nRF52 functions as an HCI controller connected via LPUART to the nRF9160. We're at the stage...
Dear sir:
When I first use CHIP tool in my Ubuntu NB, I can commission bulb(52840) through OTBR(Pi4+52840 RCP) successfully, besides, I can use CHIP tool to control bulb...
Hello,
I am currently checking the RSSI measurement precision, and we got very large errors (up to 10dB error) on the RSSI vs input power.
To avoid any PCB / matching...
I'm new to nRF5340 development, and I'm reviewing partitioning for multi-image DFU. I've enabled the bootloader with CONFIG_BOOTLOADER_MCUBOOT=y , and after checking partitions...
