Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I am developing a firmware for the nRF52805 SoC with a nRF52 DK. I want to implement the DFU support on the same. The secure bootloader example in examples\dfu\secure_bootloader...
Hi everybody,
I'm trying to update a device (a PineTime device with a nrf52832). The firmware is using legacy DFU. I already have a DFU package, so, I only need to perform...
Hi,
I running a code that written on C and compiled with IAR for few years on nRF52832. Now i have a task to implement a new algorithm on embbeded but it was written with...
Hello, I'm flash download nrf52840 use st-link.
my softdevice version is s140, nrf5 sdk version is 13.0.0.
I want to flash download project, But I have an error.
...
Hello all Thank you for the many helpful posts I have encountered on this forum while continuing to discover the nRF5 SDK.
I have been trying out different examples for...
Hello,
We are working on one project in which we are planning to place PCBA with BLE module inside metal enclose.
Does it affect broadcasting range and communication...
I am using the nRF52840 (with SDKv17.0.0 + s140_7.0.1) and made a custom FW based on the ble_app_hrs example. My HW has a 64MB NOR flash memory chip and eventually I want...
The single button in the Dongle does not generate any events. I have made all the relevant changes for the preprocessor for the usage with Dongle. Kindly let me know what...
Hi there,
I am an experienced Electronics Design Engineer. In the past 5 years, however, I have only dealt with on-board systems (hardware) such as power supplies, analogue...
Hi,
I am curious as to whether one should use the nRF Connect SDK or "vanilla" Zephyr when developing let's say a BLE application that uses multiple peripherals on the...
Hi!
I'm using the download_client to fetch one file from time to time. The app is basically a clone of the sample app, just put in a function.
The problem is that if I...
Hi,
I've been developing software that uses pc-ble-driver and a PCA10040 devkit to act as a central. My software is based off the heart rate v5 example written in C, and...
Hi,
We have been working with a Zigbee coordinator based on nRF52840 with nRF5_SDK_for_Thread_and_Zigbee_v4.0.0_dc7186b, Softdevice and FreeRTOS.
We are tring to integrate...
Hello Community,
So I am building a RF system from scratch based on the nRF24l01P transceiver with a PA/LNA, using a balun for impedance matching and a band filter for filtering...
Hi All!
Hope you all are doing well ! . I am new to nrf52833. My requirement is test the range test with CODED PHY @125kbps /S=8 .
For this i tested the example "ble_app_att_mtu_throughput...
