Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
Respected Sir, Mam
I am Noel Joe Riju Antony a student of Amity University, Noida, India pursuing a B.Tech in Aerospace engineering. I am currently working on a CW radar...
Hi,
I've got a Thingy:91, which I've spent a lot of hours in understanding the different samples. I want to be able to send GPS information to my Azure IoT hub device...
Utilizing SDK 15.2 and Softdevice S132, when debugging with Segger Ozone and starting from main or after triggering a reset to restart at main an ERROR 8 [NRF_ERROR_INVALID_STATE...
Tried running android app in debug mode, but I could not see any data on the crash.
tried resetting the board a few time and re commissioning.
followed the guide to set...
I found a lot of posts with this warning/error, but I could not find a fitting solution among them.
in my case, I copied the `peripheral_lbs` project to another folder,...
Hello
I have a few questions regarding the "ble_thread_dyn_mtd_coap_cli" example:
In the "main.c" file, I notice that you have created timers to call "sd_ble_gap_conn_param_update...
Hello.
I have a custom board with a uBlox BMD300 on it. The BMD300 is based on the nRF52382. The BMD300 had a pre package firmware in it that acted as a BLE UART bridge...
Hi all,
I am using the python bindings in recent weeks to development a BLE scanning device and have found the python bindings very useful for getting the kit up and running...
On MacOS Big Sur (11.2), trying to get started with nRF5340 samples, but getting create_nordic_project.py failed (1) errors.
I installed manually using the nRF Connect v3...
We are in the evaluation phase of a technology that is planning to use sound to transmit data between phones and devices.
We are currently using Quiet open source library...
Hi Team,
We are using the nRF52840 DK for one of our project, as part of that we are using the RNG functionality with CC310 Library.
When we call this "CRYS_RND_GenerateVector...
Hi,
I try to do the Onboarding workflow for 1NCE SIM Cards with the NRF91 Module: 1nce.com/.../
So the solution is to send a GET Request to a special endpoint and you...
We have certified the Centauri gateway with https://fccid.io/2AKNO-VOLCT200LTE ID. Now We have a query that we used nrf52840 chip as a BLE during certification.
Now on this...
Hi, nRF newbie here, forgive me if I'm being dim. I've searched the devzone, can't see obvious answers. nRF52840, SDK 17.0.2, Nordic SES 5.30a, using nrfx_* drivers I'm using...
Hi all,
I am working with a BNO080 imu and have ported an Adafruit library into the ble_app_template and created a custom service.
Independently, the IMU code and the...
