Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Hi all,
I am working with a BNO080 imu and have ported an Adafruit library into the ble_app_template and created a custom service.
Independently, the IMU code and the...
Dear Nordic,
I am running into an interesting side effect when I disable the app scheduler library from my program. I have been previously using the app scheduler to service...
Hi,
1/ Is it mandatory for Direction Finding process to have all streaming advertising messages from beacon to locator connectable ?
2/ Is it possible/easy to manage live...
Hi,
I have an application and I want to send the output of the application via CoAP LTE connection. My plan is to modify the nrf-sdk CoAP Client sample to achieve this...
We are trying to use mcumgr/mcuboot with Zephyr on nRF53. During development, we have enabled the Zephyr shell functionality and would like to use mcumgr with it (CONFIG_MCUMGR_SMP_SHELL...
Hello!
I've got a problem when performing a DFU OTA. I first flash my software(#1) with bootloader in de nrf53840DK. When i make changes to the software i use app_update...
Good day, I have seen a few people asking about connecting the Nordic devices with the RFM95/Sx1276 modules. I understand that it is SPI driven, but I am a complete novice...
Hi,
I'm using nrf52840 to connect a mobile device via BLE.
I've noticed that when a lot of messages are sent, a disconnection occurs with reason code of NRF_ERROR_RESOURCES...
Hi there!
I'm currently facing an issue where the client will stop transmitting messages after six hours and twenty-five minutes. This is the case after 255 messages have...
Hi everybody.
I'm margin two different projects:
examples\peripheral\usbd_hid_generic
with
examples\ble_peripheral\ble_app_hids_keyboard
but, using the make file...
Hi,
I am using a custom board that uses Arm Cortex-A7 and embedding an nRF52840, There is no external low-frequency crystal 32kHz connected to the nrf52 chip, so I've enabled...
Hi ,
I'm trying to use http_application_update , on an https website, and i get:
I: Attempting to connect over IPv4 I: Setting up TLS credentials E: Unable to connect...
Hi,
I want to transmit data on each button ( lets say 4 buttons for now ) press on my custom board. I have used ble_app_beacon example and tutorial https://devzone.nordicsemi...
Hello
I have uploaded USB CDC ACM example code in my custom board of nRF52840. I didn't get Vcc on D+ pin and cannot detect USB. I have also check soldering side and resistance...
