Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
As the title says, I'm getting a hardfault on a call to pm_init() in a BLE peripheral HRS trial application. This is on a micro:bit v2 board, which has an nRF52833 Cortex...
Hi, Im trying to add accelerometer value to my own service. The device is advertising, When I connect to the nRF Connect application, I can not see my service, the status...
Greetings,
I'm using nRF52 DK to transfer LIS3DH accelerometer data in Bluetooth. I successfully managed to establish an I2C connection with my sensor, I get my XYZ values...
Hello Nordicsemi Community,
I am attempting to update the firmware of nrf5340pdk cpuapp from a mcumgr cli running on a raspberry pi 4 linux. From the logs, it seems the...
Hi,
i am using a nRF52840 with sdk v17.0.2 on soft device s112. using the ble beacon example. i can set up the connection from the raspberry pi with a 2 second beacon...
Hello Nordic Team
I am working on SDK v-17.0.2 SPI example to interface with external flash memory. I have Winbond W25Q128FV and Fudan FM25Q08 flash memory but have same...
Hi,
I have modified the Cloud Client sample from ncs v1.4.0 for sending sensor values to the AWS IoT. The sensor code makes use of GPIOTE interrupts using this sample as...
Hi after a long time,
we have developed a custom board with nRF52840 and there is a part of the project, which is focused on sensing sound and evaluating sound pressure...
Hello,
I am experiencing a weird issue with a code which I wrote for my ultrasonic distance measurement sensor for Thingy91. The code works fine and gives measurement values...
Hi, I have a very odd problem but one which is consistent. As part of my lcd library I send several ''packets' of data interleaved with spacing from a timer. It typically...
Hi,
I am developing using nRF52820 / SDK 17.0.2
In order to store data in FDS, the handlers were registered and initialized as follows.
FDS_Event_handler does...
Hi.
I am working on nRF52832. I want to store a structure with 492kb I am getting heap is too large error. So how can I tell the complier to store my variable in flash instead...
Hello,
I am using nrf52_DK to debug PDM with a digital MIC, and select the pin 29 for the PDM CLK, But I haven't seen any clock signal output, for generating the clock...
I am develop a android application with BLE.
My bluetooth device can be searched by bluetooth scanning of android.
And my application can connect with the bluetooth device...
Hi,
My system is
- nRF5340 custom board - Zephyr OS build v2.3.0-rc1-ncs1 - nRF-Connect-SDK v1.2.0
To perform DFU over UART I was told to merge MCUBoot + mcumgr +...
