My goal is to control a RC toy drone (4-ch 2.4GHz) from a PC. I've seen some hacks (for example dzlsevilgeniuslair.blogspot.com.br/.../more-toy-quadcopter-hacking.html) using...
Hi Team,
Is it possible to implement the iOS application to track the iBeacon Component after closing the application(Background processing).
Please provide any example...
Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
I'm on my Windows 10 machine using Segger Embedded Studio V4.52C. I'm using SDK16 and Mesh 4.0.1 with FreeRTOS. I have built the light switch server example found here to...
Hello,
I am using SDK v1.3.0 with modem firmware v1.2.0 with the nRF9160 DK v0.9.0. I am using an AT&T SIM card to connect to their LTE Cat-M1 network.
I would like to...
I’ve not yet been able to successfully get an application (in this case Blinky) to complete a BLE DFU load and then execute. I’ve tried all the suggestions I’ve found in the...
Hello,
I would like to learn a little more about the possibilities of thin planning of connection events. I rely on chapter 15, in particular on part 15.7 of the S140 SoftDevice...
Hi, I'm trying to do the iot mqtt publisher example with the nRF5_SDK_15.3.0_59ac345, a nrf52840 and a Raspberry Pi 3 B+ as a gateway but I got some problems :
After the...
We have been testing the DK board and Thingy:91 and had a few questions on enabling PSM/queued mode.
We are able to enable queued mode for the lwm2m_client example on the...
Hi! Some prerequisite info:
We are using nrf52840 boards as our peripherals
We are using v16.0.0 SDK
We are using the s113 SoftDevice, more specifically s113_nrf52_7...
Hi!
I'm going over the nRF52820 chipset, and I'm not sure I completely understand the reference schematics in regards to the LC filters on the REG1 DCDC enabled option....
I am using "ble_app_hrs_rscs_relay" example and modified it a bit by adding NUS service and FDS. Everything is working fine with mobile app and nrf dongle. How ever when I...
Hello,
I am trying to setup my project's architecture and I am trying to take advantage of some of the awesome libraries in the SDK. I am a bit confused on the differences...
I ran into an issue using RTT on recent SDKs: In SDK15.3 and up RTT stopped working in Segger Embedded Studio. Here's what I found in case others are having the same issue...
Hi,
We are having single Main supply VDD to nRF9160 SoC, which is powering both CoreM33 and Modem.
So this indicates Modem will be always ON when Core M33 is ON.
Is...
Hi everyone,
Following some tutorials as well some examples provided by SDK16 I was able to create a custom service with a characteristic that has read,write and notify...
