Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I've recently began experimenting with the HID service and connecting to iOS devices in order to achieve lower connection intervals with Apple products (as described in their...
Hi
I have a coupe of dongles working on a project. While validating the board, i notice a strange behavior: I have the dongles in factory reset (MBR at start, the Bootloader...
Good afternoon
i have built a small program for the uarte, using the example however im not managing to edit the event handler such that depending onthe text i recive...
Had tried to build it from the IDE before. Couldn't do it. Tried to build manually, got exactly the same error I was getting in the IDE. Parsing C:/Users/mario.raposo/zephyrproject...
Hi,
i have followed a few manuals like this one: https://www.nordicsemi.com/Software-and-tools/Development-Kits/nRF9160-DK/GetStarted#infotabs
or this one:
https:...
I'm trying to make an application which displays signal transferred via bluetooth.
To reduce computing time on the tablet, I want to apply oversampling in nRF52840.
The...
Thanks in advanced. I achieve 4 uint8_t dynamic sensor datas, I want 52832 transmit them through BLE continuously. Based on examples\ble_peripheral\ble_app_gatts_c, I can...
Dear,
How to evaluate a channel if is clear in property in NRF528 serials? e.g. there are ED and CCA in 802.15.4 standard, how to implement CSMA in NRF52810?
Hi
I'm using nRF52832, SDK 16.
When I enabling timer application the power consumption is increased by ~450uA, far away from the product specification
What may cause...
Hi there,
We're trying to write to the UICR CUSTOMER register to store some of the manufacturer info, such as BLE MAC address, for example.
When SD isn't running we have...
The following is loaded into flash on the nRF52840: Bootloader: 0xe0000 Application: 0x27000 SOFTDEVICE S140: 0x1000 MBR at 0x0000
Bootloader starts, waits 5 sec and runs...
Hello,
I want to use BLE direction finding. In the product brief ( https://www.nordicsemi.com/-/media/Software-and-other-downloads/Product-Briefs/nRF52833-DK-PB-10.pdf?la...
Hi,
I need some help to interpret the LTE timers values that my network operator applies.
During network registration I requested RPTAU : 10 min and AT : 0 min, by issuing...
I want to connect the nordic ZigBee with Digi's XBee module.
I have configured the Digi XBee pro s2c module as coordinator and nordic as a router but they are not communicating...
Continuing the discussion that was documented here:
https://devzone.nordicsemi.com/f/nordic-q-a/64691/how-to-use-the-latest-version-of-californium
1) I modified the resources...
Dear Nordic Support Team,
I haven't seen any forum posts directly applicable to the issue I'm seeing so I hope you can point me in the right direction.
The basic Thread...
