Hi,
Will PAN item #56 TWI: TWI module lock-up be fixed in the Rev 3 version of the nRF51822/51422?
Also would you happen to have a time frame as to when the Rev 3 will...
Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
Hi to everyone!!
I have this error:
.\_build\nrf52832_xxaa.axf: Error: L6218E: Undefined symbol nrf_fprintf (referred from nrf_log_str_formatter.o). .\_build\nrf52832_xxaa...
Hello, I attempted to make SES thread aware by following various support threads in this forum but unfortunately the SES just doesn't show any threads. I have tried with 2...
Hi,
I running a custom application on nRF5340 PDK using zephyr (2.3.0) and nordic SDK (1.3.0).
I tried to build Zephyr HID examples and got an error. (I don't think it...
I am using an example from Nordic that enables a central to connect to several peripherals via UART. The connection is automatic (the key is if they all share the same NRF_UART...
OS in development environment ：Windows10 HARD :(Taiyo Yuden)EBSHSN Series Evaluation Board : Central / Peripherals CPU :(Nordic) nRF52832 / ARMR Cortex-M4F 32 bit processor...
Hi, so i'm using Visual Code with PlatformIO to build an example with arduino-bluefruit-bleuart the build runs perfectly but after i upload it into the Nordic the bluetooth...
Dear Sir, I need 2 interrupt handle on 2 PIN, I have set 2 GPIOTE event: #define PIN_INT1_ACC 4 // INPUT Interrupt INT1 from ACC #define PIN_INTB_ECG 8 // INPUT Interrupt...
Hi, I have a set up consisting of an nRF52840 and Raspberry Pi communicating over IPSP following the zephyr OS sample docs.zephyrproject.org/.../README.html My application...
Hi,
I've been using XMONITOR command to check some radio parameters. ATM, I am checking those once/minute, right before requesting power save mode from modem. After updating...
Hello,
I wondering if I use the nrf5_SDK_for_Mesh_v4.2.0_src light switch example and modify it to suit my needs.
Q1. I want set up a proxy node using nRF52832 so that...
Hi,
in https://devzone.nordicsemi.com/f/nordic-q-a/24115/io-pin-signal-during-reset it is mentioned that the pins of the nRF52832 get set to input _during_ a reset.
...
This is my RTC init function. Whenever I start advertising in fast-advertising mode, and timeout for fast advertising expires, the RTC2 timer stops running and COUNTER resets...
Hello,
I am trying to make a simple power optimized BLE peripheral device based on nRF52840.
Here is the chart from the Power Profiler
The device advertises once in...
Hello,
I am trying to use "west" command in Eclipse but I am not able to do it.
I was able to do that in Visual Studio though.
I found this link https://devzone.nordicsemi...
