Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi,
I am using ancs service to get some information of my iphone.
I use nRF51822 microcontroller and Nordic suggests to use the new SDK (5.2) for new microcontroller...
Hi Nordic Team,
In my BLE project, first the central device starts scanning, then the peripheral device starts advertising, the peripheral device gets connected to central...
HI,
I got nrfutil + BLE DFU app update working using the ble_app_hrs for the test. I am using the nrf52DK + SES for development, and I have also an external nrf52832...
Hi
I'm using this simple_pwm code to drive my speaker, I use this as a buzzer but I want to change the frequency.
In this code ".base_clock = NRF_PWM_CLK_125kHz", the...
Hi, I am developing an IMU app communication with ESB. I would like to send to the board a command with ESB to put the nrf52832 board in BLE DFU mode.
I have look at the...
I am using the timeslot API, and I have noticed that if I read Timer0 as the first thing in my timeslot, it will be at 75 us. This delay is very consistent, so my timing between...
The following change was introduced in v4.0.0
Note that mesh_config_clear() was replaced with mesh_opt_clear() which is a rather big change of behavior that wasn't documented...
Hi,
Just trying to run mqtt sample with TLS and AWS IoT backend. Everything worked fine in the beginning, but then after I tweaked the code a bit I suddenly started getting...
Hello,
I'm using SDK5 v16.0 and softdevice S140 v7.0.1.
At some of the PCs, it takes much longer than usual to upload the zip package. On my machine, the transfer rate...
Errata 182 needs to be applied (in revision 2 devices) to enable the fix for erratas 102, 106 and 107. The workarounds for these erratas all stated that they reduced receive...
Hi,
I am using NRF51822 SDK12 S130, I have increased my code and encountered a crash right at the beginning, I debugged it as follows -
I increase an integer ( uint32...
Hi,
I was wondering if I could get a little information on how to set a pin as High Impedance using the zephyr gpio.h library.
We have a shared pin between a nRF9160 and...
Is there a value or values range defined for the user cmd/evt in the serial interface?
I would like to use the uart for some app specific operations, and could use packet...
Hello. I'm having problems to programme the nRF52832. I'm just connecting the VCC (+3,3V), GND and SWDIO and SWDCLK. Is it ncessary to connect any other devices like capacitors...
Hello,
I have been using the buttonless DFU method for a while on the nrf52832 Chip. Due to performances need we changed the chip for our product from nrf52832 to nrf52840...
