Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I have been experimenting with the example of the MQTT Client Subscriber/Publisher from de nRF SDK. I use:
SDK v15.3.0 (also nRF5 SDK v15.2.0).
Raspberry Pi 3 (as a...
Are there any working projects that integrate TWI and MPU6050 sensor. That are edited by KIELu5 and follow the SDK 15.3v ? I tried modifying the 'twi_sensor' project but I...
Good day
Im trying to switch off an LED when my relay/hopper is not advertising. I switch the LED on successfully when transmission starts but I'm struggling to do the sd_ble_gap_adv_stop...
Hi, everyone,
now I'm test " \ncs\nrf\samples\nrf9160\gps\build_nrf9160_pca10090 ",
it's error about" nrf_socket.h: No such file or directory"
I'm find the file at ...
So this is a small continuation of this ticket https://devzone.nordicsemi.com/f/nordic-q-a/50656/using-pdm-mic-on-nrf9160dk .
The problem I'm having now is that when I run...
I wrote UART echo sample based on ble_app_uart_c for S140/ nRF52840-DK.
When nRF52 receive one line on USB/UART, it send same line to USB/UART.
I also write Linux socket...
I am following this tutorial:
https://devzone.nordicsemi.com/nordic/short-range-guides/b/software-development-kit/posts/application-timer-tutorial?CommentId=43347679-22d9...
Hello,
I want to use the ADC for a burst @ 8khz.
I use this sample " test_adc_sample_with_interval " from https://github.com/zephyrproject-rtos/zephyr/blob/master/tests...
Greetings...
Please help me understand why PB-GATT support is removed from SDK UART coexistence example?
The dilemma I am facing is as follows:
1. No PB-GATT for SDK...
Hello, Currently, we trying to use PPI with the SPI module (we use the SDK 15.3.0) We expected that the SPI makes one read transaction every 5 us ; to do this, we use 2 PPI...
Hi there,
My project needs TrustZone and ETB feature. The manual clearly states that the board supports TrustZone and ETM. I wonder if it also supports ETB to store trace...
Hi,
I am using SDK15.3 with the SoftDevice enabled. I've been unable to get any SoC events after making a call to sd_flash_page_erase. I registered my observer as follows...
I'm trying to develop a Bluetooth application where my Nordic nrf52 DK sends an event when I push the button and another when I release it.
I'm trying to apply this on the...
Folks,
One of the devs here found that all warnings were switched off in SES, so I've recompiled and got rid of most of the 1400 odd (sic) warnings by suppressing unused...
