Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Hi
I want to get the RSSI value of the received packet through the DTM test routine. Here is my DTM test routine, where I changed it
I got the result
>> RSSI: -127...
Hi
I am trying to create ble mesh network using 4 different N52832 module. But every time i tried to connect with the network, received the initial configuration failed...
Hi,
I'm interested in using Gazell and have managed to get the gzll_ack_payload Device & Host examples working successfully between a pair of nRF52840 devices on our custom...
I tried to install the latest nRF Connect (3.1.0) on my Windows 7 dev machine and it did something to wipe out my USB setup (froze up during install of JLINK). So I had to...
Hi all,
I'm working on a board equipped with a nRF24L01+. It is PIC32 based and I'm writing a mini driver for it. So far my SPI and API seems to work correctly:
...
I wasn't able to find any documentation or examples for the BL-651 chip which is meant to run the same code as the NRF52 bluetooth chip.
I'm having trouble running it on...
Hi everyone,
I'm using a Si7051 I²C temperature sensor connected to a nRF52840 and I found some very weird behavior of the TWIM module. Firmware-wise I'm using the mbed...
Hello All My English is not good, so Sorry I have a question like this
I have self BLE unit - EYSGJNAWY-WX from TAIYO YUDEN firm That has nrf51822 CPU and 32.000 crystal...
Hi there,
I would like to know why v4.22 version of SES doesn't have "nRF Connect" tag under " Tools→Options "
also I even can't find "open nRF Connect SDK project" option...
Hi,
I have an app that uses freeRTOS
My app runs OK , however when I am debugging it in segger studio with my SWD connector, it crashes with no reason
If I check the...
Hi,
Do you have a basic Android Studio App that can connect send and receive from an nrf52832 based board already programmed?
I know the protocol strings I need to send...
Hi I am porting my application from SDK12.3 to SDK15.3.
I am facing error during advertising. Below is the code snippet and error is invalid param (0x07).
For scan response...
Hello everyone. I am working on an RTLS application that uses BLE's RSSI measurement method (Using nRF52840 dongle) to locate a human. The system has 3 components:
Beacon...
Hello, It looks like if there is an issue with bootloader DFU. If no connection timeout is right. But if you starts a DFU late (near the end of the timeout), il will cut during...
I intend to check some of the NRF_SOC_EVTS in my application. Where should I register soc_evt_handler(uint32_t sys_evt, void * p_context) function? Will this function be called...
