Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I've recently began experimenting with the HID service and connecting to iOS devices in order to achieve lower connection intervals with Apple products (as described in their...
Hello, I am trying to change the data length(maximize) from Nrf Connect Desktop to a BLE5 device. Could someone help me, how to change the packets size being sent? Thanks...
Hello All,
I am using the example " iot_secure_dfu_bootloader_secure_dfu_s132_pca10040 " with the NRF52 DK board.
I have build and load the code in the board but it...
I want to know how to add custom field in the firmware package generated using nrfutil? I generate three firmwares but sometimes its error prone, I saw wrong firmware flashed...
I have used ble_app_uart example as the base project and have added FreeRTOS and SAADC example to it. And I get the following errors as attached in the image.I have added...
Hello,
I have merged nrfx_spim and ble_app_uart. I was testing the spi tx function as my application has specific timing requirements. I have experienced something that...
chip: nrf52832
sdk:nRF5_SDK_15.3.0_59ac345
my purpose: i want to store data to flash from ble_uart
demo: examples\ble_peripheral\ble_app_uart and examples\peripheral...
I followed strictly all steps of the nRF Connect SDK Getting Started Assistant. However, the code doesn't compile:
(...)
9> Compiling ‘reboot.c’ 1> In file included from...
Hi, i am working on a bluetooth application with the nRF52832. When i try to connect a Samsung Galaxy S8 (Android 8.0) via nRF Connect, i get a LMP TIMEOUT error after 40...
Launch, then select 'Launch Programmer, tool displays message "The app only supports nRF connect ^2.5.0 while your installed version is 3.0.0. It might not work as expected...
From what I could see the Asset_Tracker example works in LTE, not in NB-IoT. How can I test NB-IoT?
I would like to get some hint on what example to use and what to do to...
Hey all,
I'm a bit lost here... I developed a wireless sensor for a customer based on the nRF52840 and it works great. Now we're developing a small light weight gateway...
Hi everyone,
I'm trying to developp a MIDI USB class compliant device with the nrf52840 DK.
I'm beginner about USB developpement and I have only basics about MIDI class...
I am using SDK 15.3.0 working on nRF52832, on windows platform.
Our requirement is, we need to get the data from both nRF52832 and BLE Heart rate sensor at same time and...
I have developed a new board based around NRF91 module. Ten prototypes are produced and six of them work. Other four devices cannot connect to the LTE network. I am using...
Hi,
I'm using nrf_serial to configure and then read data from a GPS engine, but I am getting unrecoverable OVERRUN errors on start-up if the GPS device is sending data when...
