Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi All,
I have an application running on the nRF52832. From within the application I can store data to 0x2000 2010 - 0x2000 2028 and read the data back after a reboot/power...
Hi,
I need to generate a PWM signal with exact 2.048 MHz. I've just realized that
allows only decimal frequency. Even if I take 16 MHz and toggle it every 7,8,9 still...
Hi,
I have the NRF52 dev kit with NRF522832 chip. I am using SDK version 15.2 and the Segger IDE. I am trying to do OTA programming and have used this tutorial:
https...
I followed the nRF User Guide v2.2 for my nRF dongle and all was Ok up to "Install firmware with SEGGER J-Link point 6 e (loadfile Path\...\sniffer_pca10031.hex)". Got error...
Hi!
I am trying to get this example to work on my nRF9160 board: https://github.com/Rallare/fw-nrfconnect-nrf/tree/nrf9160_samples/samples/nrf9160/spi/
It compiles and...
Hi,
if got the following setup:
Nordic nRF52840 DK (peripheral), custom iOS App (central), nRF Connect Desktop Version + another nRf52840 DK as sniffer.
My Goal: Changing...
Hello,
I need to interface both, an SD card and a smaller (~4Mb) external flash to the nRF52840.
The SD card will be interfaced using SPI.
For the external flash...
I would like to store some parameters in nordic's non volatile memory and be able to restore them after power off.I am using the soft device s130.
I have checked both examples...
I have made a HDI 4-Layers PCB. I referenced the example PCB, but my board it do not work.
The softdevice is:s132_nrf52_6.0.0_softdevice.hex
The example code is: ble_app_uart...
Hi all,
I follow advice here " devzone.nordicsemi.com/.../nrf52832-ble-scan " to do the ble scan, I have question that there is a function to store scanned ble to the list...
Hello,
I generated the assets tracker sample project (like in this image below).
After building all the projects, I want to connect to jlink to download the project...
when i downloaded a git-hub ble-advertising tutorial and then tried to compile using segger. it gave me this error.. i am using nrf_sdk_5.2 and soft_device of S140.. i cant...
Hi,
I've got a suggestion to use for nRF52832 Multilink Universal FX or Cyclin FX programmers.
Even though the Segger programmer only suggested by Nordicsemi.
Can you...
Hi,
Last week I bought two NRF9160 DK. I downloaded the nrf connect on pc and then i followed the steps carefully from this webpage https://devzone.nordicsemi.com/nordic...
Hi,
I'm trying to send out 3 bytes just before I reset the chip. I am using nRF51, SD 130 1.0 and SDK v10.0.0. UART works well in other parts of code.
My original solution...
