Hi Team,
Is it possible to implement the iOS application to track the iBeacon Component after closing the application(Background processing).
Please provide any example...
Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
I want to send data to all node by mesh 2.1.1.
From the Mesh profile(3.4.2.4 Group address),the dst_addr = 0xFFFF is send to all node .
I try to setting "packet_tx()"funtion...
Hi,
Currently im working on creating firmware for out device based on the nrf52832. I have structured my project where i have seperate files for each module i am creating...
The hid keyboard example includes the battery service. But how does it work? I would like to monitor the battery charge. After I use the voltage divider, to which AIN pin...
Hi,
I have NRF51DK (PCA10028) board and i want to flash BT832 (NRF52832) device.I have downloaded latest SDK but it only has the option of PCA10040.Is it possible to flash...
Hi All,
I've problem with nRF52 programming. I want to verify uart by using examples placed in the NS SDK for nRF52. After I loaded uart example, uVision shows error in...
Hello,
I am looking into the Power Profiler Kit for measuring the power consumption of a custom hardware. I can see that the PC Application is really useful during development...
About this example
https://github.com/NordicPlayground/nrf51-ble-tutorial-advertising
It´s advertising the data
uint8_t data_response[] = "Many_bytes_of_data" with the...
Hi,
I was working with MCUBOOT and was curious too know from where the MCUBOOT release version number is been generated or fetched-
When building MCUBOOT using cmake...
Hello mates,
I am modifying the Light Switch Client and Server example, to send messages uint8_t from the client to the server instead of use bool on_ff with no luck yet...
I am currently using a 51dk board. I am trying to study low power system_on_wakeup_on_gpio in github. I built this code and measured the amount of current. I would like to...
Parameter setting code is shown below. I've verified that the settings are being reported back in events, so they seem to be taking place. However, I'm keeping track of the...
I am trying to get the application to enter DFU via the buttonless DFU service using SDK 15.2. It appears to be stuck because of an SVC call not returning. Both application...
Hi :)
I would like to test the nRF52840-Dongle in a Raspberry Pi 3B+ OS = Rasbian (the bluetooth 5 features: 2Mbps and Long range). but unfortunately I didn't find a nRF...
I'm looking for a gateway (or BLE 5.0 device that can connect to a gateway, e.g. USB dongle) that uses the nRF52 series solutions with an amplifier that brings the transmission...
Sir
We have a client that is using two NINA B3 (uses a NRF52840), one central and other peripheral. The peripheral is sending advertising packages, but the central is only...
