Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
There aer a couple of ifles in the SDK that use this weird _H compiler directive that prevents them from compiling - how do you control those? For example, NRF_SORTLIST_H...
hi, new to ble so forgive me if my question is a little simple. i have a project that for example would require 10 central devices and 3 broadcasters. centrals and broadcasters...
hi, new to ble so forgive me if my question is a little simple. i have a project that for example would require 10 central devices and 3 broadcasters. centrals and broadcasters...
Hello. I am trying to connect nRF 52840-DK and LTC 5800-WHM with UART. The communication conditions are as follows. Baud rate: 115200 Data: 8 bits Stop bit: 1 bit Parity:...
Hello Community,
I am trying to use Black Magic Probe, an open-source ARM GDB debugger to develop an embedded ARM application using an nRF52832. Here are the parts that...
I am trying to configure two ports as outputs, setting them to Vdd and toggling them. The two ports in question are Po.06 and Po.07.
Here is my code to configure these ports...
Hi,
I didn't understand the function of softdevice. I have a custom nrf52832 board. My requirements;
-2 uart,2spi,1i2c
-OTA update
Should i use a softdevice in nrf...
I have been playing around with example projects in SES (I'm using SDK 15.2.0, SES version 3.52a).
Now wish to start a project from scratch, and import libraries from the...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
We work with custom firmware and use the softdevice 2.0.1 on the nrf51822
I upload the firmware as .zip file using the android nrf Toolbox, which works fine, but when performing...
hi there,
i have made the application and dfu working but there is a smal issue. if i program dfu and application from nrfgo studios the dfu run continuously and app does...
Hi, I'm trying to use the light_switch example in the Mesh SDK 2.1.1 to build a small experiment to count how many messages are received by the server when sending a consecutive...
Hello,
I am trying to do USB DFU on (NRF52840 with SDK 15.2) but when i run the nrfutil command it gives an error:
command: nrfutil dfu usb_serial -pkg ble_hrs_combo...
I've setup, compiled and run the BLE Beacon project an have made some changes. Now I need to enable the UART. Simply adding UART files to the project does not work due to...
