I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hi @all
I'm searching for a nRF905 breakout board for the 868Mhz band. All I can find is nRF905 boards for 433Mhz (e.g. rfinchina or freqchina). Anyone tips where I can...
I'm trying to pair a Nordic SDK15 central to a non Nordic peripheral ( BLE 4.0)
I have no IO for passkeys
I'm testing by pairing Master control panel ( is it BLE 4.2?...
Hello team,
Having a bit of an issue. The link for the S140 SoftDevice results in an "Access Denied" page.
Origination Page >> https://www.nordicsemi.com/eng/Products...
Hi Everyone
I am able to configure BLE on the template project and it is sending data from nrf52840 to BLE nrfconnect app using the function nrf_ble_data_send() .
However...
HI All,
I am trying to upgrade sdk v11 to sdk v13 in my project and after compilation i am facing Linker Error as mentioned below.
binaries/app/SmartTag2/dfuFlash.c.o...
Hi :
I have the same problem. I try to flash program to the Dongle using MCP. Every time I program the Dongle, the MCP log report: "NO response from master emulator". What...
Hi all,
I am using SDK version 15, SES IDE.
I am working on Dust sensor, for that i am using SAAADC example code, I want to read the ADC value from the pin, like this...
Hi Sir,
Based on the nRF5-SDK-for-Mesh , it mentions " release with a Bluetooth mesh profile v1.0 qualified stack".
Do we already have the QDID information for Mesh profile...
Hello,
Can i implement same functionality provided by NXP Mifare DESFire EV1 to nRF52832?
If yes, where i get the details and reference code for the same.
I want...
Hi Sir
I tested the cli example or uart example of SDK15, the uart response data are wrong and slowly.
I have no idea what happened. please help.
------------------...
I am currently using mesh sdk 2.0.1 and I plan to migrate to 2.1.1. I saw this while comparing the light_switch example of the two sdks.
proxy server is not supported...
I am using nrf52832, and used mpu 9250. I want to store the data of mpu 9250 in external and internal flash memory. will you help me how to do this?
the odr of sensor is...
Hi,
I am developing an application using the nRF52840 as NCP with a raspberry pi as the primary processor, using wpantund. I have 3 devices (3 raspberry, each with its own...
