I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello. We evaluate DFU using nRF 52840. After writing sd_s140_bootloader_buttonless_with_setting_page_dfu_secure_ble_debug_without_bonds.hex to nRF 52840-DK, we updated using...
Hello,
I'm playing with nRF52840 on a custom board, trying to connect to the chip via SWD. Segger Flasher is being used, on MacOS. Typically I was able to connect to the...
Hi,
I am having issues to program a NINA B112 using the debug out port on the PCA10040 development board connected with a tag connect 10 pin cable, but when trying to program...
The project is cobbled together, but starts from TWIsensor in the SDK 14 examples. The project is compiled with the gcc toolchain which has not given me any trouble. The project...
I am trying to use UART with interrupts and fifo, by using nRF52 SDK 12.2.0 example. It works until the first overflow, after which I cannot any more receive characacters...
Hi!
I'm using an NRF52 with app_uart. As expected at 115200 baud rate, I occasionally get overflow errors which I can see in my event handler.
However, after these errors...
Hi,
Where are scan requests sent? I'm trying to find the function that does this because I would like to disable it.
I only want to connect with a peripheral based...
Hi everyone:
I am using the NUS (nordic UART service) in my project, and find one problem in this project. The development bench is: SDK13.0, nRF52 DK.
If I build a NUS...
Hi,
I used IOT TCP Server example of nRF5 SDK(Ver.15.0) to complete the communication
between the Raspberry Pi and the PCA10040.
But I found that the communication speed...
Hi,
1. I want to disable MCU UART connection which is SB with GPIO pin 5, 6, 7, 8 and I need to connect that pin on arm based processor so desoldering those short bridge...
Hello,
we are facing a weird issue with a few models of smartphone since we increased the max MTU size. We are testing at the office with the Xperia E6553 but the Samsung...
Hi there
I am stuck. My incremental wheel with photocell and comparator circuit does not work if the QDEC hangs on it. But seperately it works fine.
When I hang it to...
Hi Team,
Which models are supported in the latest mesh SDK?
I can see support for the on-off model.
Is Time and Scenes (Explained in Mesh Models.pdf, Section-5, Page...
I use SDK13, nRF52, S132
I use bootloader_secure_ble with generated public key for bootloader and for nrfutil. After all steps like discribed on
devzone.nordicsemi.com...
