Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi,
I am using ancs service to get some information of my iphone.
I use nRF51822 microcontroller and Nordic suggests to use the new SDK (5.2) for new microcontroller...
I'm planning to make a custom board using Thing52, following the reference desing. I have some questions (1) Can I use nRF52840 instead of nRF52832? (2) Do you provide an...
To reduce power consumption during sleep I have to completely disable the UARTE0. This is done before sleeping by :
NRF_UARTE0->TASKS_STOPRX = 1; NRF_UARTE0->ENABLE = UARTE_ENABLE_ENABLE_Disabled...
We are using Bluetooth Developer Studio along with Nordic's code generator plugin (Nordic Semiconductor nRF5 1.3.0 SDK 14.0) for our project.
We've made a couple of improvements...
Hi!
I got an error while compiling the proxy client example in BLE Mesh SDK V 2.0.0 as The object file build/light_switch_proxy_client_nrf52832_xxAA_s132_6.0.0_Debug/obj...
HI al
I have a bicycle computer (A) host (SDK 12.1 51822QFAC S130-V2.0.1) and a slave device (B) for measuring bike speed and cadence (using 2032 batteries). 1. When the...
Hi, I was recently asking about OPUS - https://devzone.nordicsemi.com/f/nordic-q-a/32875/how-compile-opus/128181#128181 . Now I am able to run encode on audio data and decode...
Hi
We have a nrf51 dongle for use in a school prosject When the nrf51 dongle is connected to the USB slot in a computer it boots fine without holding the button when powering...
On the Getting Started page, I do not see the USB described in Step 7. I do not see any device. The LEDs flash and the buttons light up LEDs 1-4 as described.
Thanks
Hi,
I'm using nrf_serial 'object' in order to communicate nRF52832 with an external device.
As I work in non-blocking mode I need to verify if there's available space...
Hi,
We are migrating SoftDevice 5.0 -> 6.0.0-6 alpha on sdk 14.2 (s132->s140) in order to be able to evaluate long range. During the migration we stumbled across some problems...
hi all,
I have an issue with hardware in the circuit, which is designed by my self. The PCB has designed a customized
condition:
I have erased full memory and measure...
we want to support the serial bootloader with SDK13, but find that the example is Experimental: Serial Secure DFU Bootloader, can we use it stably? the SDK14/15 don't Experimental...
I am using nrf52832_xxaa and SDK11.
Is there any formula that states the relation between the advertising & scanning parameters(advertising interval, scanning interval,...
I am trying to flash the program into my custom board. and i am successfully flash the program into custom board. I have flashed the blinky code in y custom board. it's works...
Hi everyone,
I would like to know in the ble_app_uart_pca10040 where the Bluetooth antenna is connected on pin planner to be able to change it.
Thanks you for helping...
