Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Hello,
I have a question about the NFC tag. In the example nrf_url_record_pca10040 there is a part where the url will be written in the tag
err_code = nfc_uri_msg_encode...
I develop ANCS success in S110,but in example ble_app_hrs_rscs_relay of S130 SDK9 .I don't know how to add the ANCS.I find S110 has ble_bondmnngr.c file,but in S130 dosn't...
quick-stop_2_with_soft_filter_NRF52_DK (1).hex I imagine that my question is just one from lack of experience. I apologize for that but I cannot find any information on the...
Hi!
I would like to use long button press to send device into sleep mode (using BSP module). Since button is tied to ground, when device goes to sleep mode, and when I...
I need to us an external RF amplifier that requires TX and RX control lines. I'm looking for a way to tell when TX starts to kick the unit into TX mode. I also need to know...
Hi,
We use NRF52832-based BLE module running serialization (SDK 14, softdevice 5.0.0) and STM32F407 MCU running application firmware on a custom board. The project is created...
Hello!
I am looking examples for nRF5_SDK_14.1.0 (For example - ble_app_eddystone )
I need read all attributes with ATT_Read_Blob_Req command.
I can read Device Name (0x2A00...
Hello,
I am using nrf 52832 and sdk 14.0.0. and i am using "ble_app_uart".
I am developing an iOS application.
Its purpose is character transfer.
I want to transfer...
Hello,
I did a quick test using 2 nRF52840 kits to measure the change of the RSSI value based on the distance and the used PHY layer.
For each test, I configured both...
I was reading through the documentation and it mentions you need;
One PCA10028 or PCA10040 development board for the client.
Three development boards or dongles...
Hi,
Is anyone successfully using MMD with the nRF52840 PVK, SES 3.3, recent SDK (e.g., 14.1.0) and S140 softdevice?
I followed the steps in this blog post both on Win10x64...
Hi.
Our company is designing a new device using the nrf52832 chip for BLE communication with other equipment from our Company.
Does the chip come with a factory preprogrammed...
Hi
We are developing ble peripheral application for the nrf52832 using SDK v13.0.0. and everything was working correctly until we tried ble connection with the iphone 7...
Hello Sir,
I have developed my application using nRF52832 chip with BLE connectivity. My device is battery operated and hence i am looking for WiFi chip with small size...
I have three questions about using AES CCM encryption by S132 timeslot API.
Is there an example value for the time request parameter in sd_radio_request(), when using...
