Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi,
I am using ancs service to get some information of my iphone.
I use nRF51822 microcontroller and Nordic suggests to use the new SDK (5.2) for new microcontroller...
Dear sirs,
My purpose is to transmit stereo HiFiaudio from one source to two speakers wirelessly.
The speakers have their own power amplifier.
The problem is that the...
hi,all
S110 NRF51822 SDK8.0.0 server
i want to increase the througout speed,the SDK8.0.0 support changing MTU size?
MTU Can be in 4.0 protocol is modified?
if SDK8.0...
Hello,
I am starting to create a bootloader and I want it to be independant of the SoftDevice. Is there any open source implementation of a flash_write function that I...
Hi
officially for the nrf51 chip, 40 ppm frequency tolerance recommended but I'm not able to find this much of tolerance in digikey.
The only matching crystal digikey...
I am trying to get a NRF HRS central (ble_app_hrs_c) to make a connection to a NRF HRS peripheral (ble_app_hrs). However, the peripheral does not show up whenever the central...
It seems like a really great company, but after exploring and asking , and searching for a good BLE solution, I just can't find a good fit.
So you want a GOOD processor...
What is the Best way to send float over BLE?
Values range between -2.000volt and +2.000Volt (-2000mV / +2000mV)
Do I break it into two uint8_t and manipulate the +/- sign...
I am engineer, and I may be sensitive to user experience, or just a bad engineer but I do not get this.
I read ALL the guides available in the last 5 hours,
this
this...
Hello,
I have just migrated my project from sdk 9 to sdk 12.2....and of course from Device Manager to Peer manager. My initial project which was built off of the sdk 9...
During the webcast earlier this week, we were shown a phone pairing with the nRF52 dev board using NFC.
Is the code used for that NFC demo available as an example project...
Hi,
I am using nRF52832 as the core of my device that works with battery. I have to keep the SoC powered on all the time. When the off push-button is pressed I restart...
I am using a nrf52832 to communicate via UART to a GSM module (AT commands).
I have setup the device with a baud rate of 9600 and using HW flowcontrol. The nrf52 is doing...
i want to communicate nrf52dk with arduino over spi.i want use nrf52dk as a master and ardunio as a slave.kindly refer me some example or code or any thing which s helpful...
Hi,
I'm working on migration from project based on SDK12.1.0, 132SD3.0.0 (calling A project) to the one based on SDK13.0.0, 132SD4.0.2 (calling B project).
I developed...
hello,
Please let me know why the BLE_GAP_EVT_DISCONNECTED event does not occur even when I exit the application.
It does not always occur when BT smart setting is enabled...
