Hi Team,
Is it possible to implement the iOS application to track the iBeacon Component after closing the application(Background processing).
Please provide any example...
Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
If I used a nrf52840 bluetooth5 as a server, but customers have iPhones with Bluetooth 4.x on, will the range still be 2x or 4x, as stated by BT SIG?
Did Nordic test the...
Hi!
I am having trouble with DFU. When I try to send new application via NrfConnect, device goes to bootloader, but file transfer is not starting. Only when I reconnect...
I started a new software project on the nRF52832 a couple of weeks ago. I've been using Segger RTT for a lot of debugging with no problem throughout the beginning of the process...
I'm using s110 pheripheral mode in my application. I want it to be in sleep mode and do not advertise untill a central want to connect it. Is it possible, when a central start...
Hey guys!
I face a problem that I have not been able to solve since several days...
I would like to send only one advertising frame every 4 seconds. I do not want to...
I am spending the last 3 days trying to make sure somebody on this plant made it using a mac .
Write a simple program and flash it to the DK. (before we make our own pcb...
Hi,
I'm using nrf51dk board and nrf_log came out correctly on my RTT terminal with built in module. After that I use debug port (P20) to program to my custom module. I've...
Hi,
I have changed in my services so I have added 0x2A05 (service changed) characteristic in my 0x1801 service. But I am not able to read the service.
In didDiscoverServices...
Hi, i'm currently using two NRF52 (1 central and 1 peripheral) using the ble_app_blinky and the ble_app_multilink_central.
I would now like to connect my Android phone...
HI:
I'am an engineer of BLE. And II want PC&Mobile connect my BLE equipment(51822) by type in password like wifi or most of bluetooth Headset.
what should I do. which paragraph...
Hello,
Is there a mechanical specification document for the nRF52 development kit (PCA10040)?
I can extrapolate from the Arduino Uno Rev 3 specification (P1-4 connectors...
hi dear Engineers,
I am affraid to use FLASH to manage PEER data, it is wrong way because of Wr op. limitaion.
Instead of that, EEPROM or FRAM must be used anyway.
How...
Does single bank bootloader in SDK7.1 support ZIP-file ?
I get error REMOTE DFU INVALID CRC ERROR in the end of flashing by nRF Toolbox when I use ZIP.
If I use hex-file...
Hello,
I am trying to implement OTA firmware update using Secure DFU.
SDK - 12.2
Softdevice - s132
Board - PCA10040 (nRF52)
I followed instructions mentioned...
