Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Hi All,
We have been developing device with pca10028 evaluation board and in the process we use also few other custom boards with nrf51822. We use IAR. The device system...
Is there any recommended value for PSTORAGE_MIN_BLOCK_SIZE or is it completely system determined. The commends in pstorage_platform.h are somewhat unclear.
If I only require...
Hello.
I want to migrate function of "sd_ble_gatts_value_set" to nRF52 from nRF51.
I use nRF52832 ,S132 and PCA10040.
I saw documentations about the function.
infocenter...
Hi. I'm using PCA10028, SDK10.0.0, S130.
I want to go to nrf_drv_uart_uninit(); right after sending data.
in order to save current consumption.
So I made source code...
Hi.
I'm using nRF51822, SDK10.0.0, S130.
Hex files : Soft device, Application, bootloader.
I want to download at once.
How can I combine Hex files to make them 1 file...
I'm trying to piece together how to be able to get this migration to work OTA via DFU. I was told by Nordic that all you need is to .zip SD8 + Boot(SDK10) and DFU both to...
I'm using:
nRF51422
SDK 7.1.0
Softdevice S310 2.0.1
nrfjprog.exe v 8.3.0
JLinkARM.dll v 5.10m
If I use the Segger with nrfjprog.exe to upload the softdevice...
I am a bit confused about what happens to ACK_PLD when ack payload packets are lost. I am assuming that in case of ack payload packet loss MAX_RT bit in STATUS is set.
...
Hello,
i have a nRF51 DK 1 and the Dongle to test and try some BLE applications.
Now i want to test how long does it take to establish and close a simple connection.
...
Hello,everyone,I encountered a confusing problem.
My device is nrf51822. I want to test whether the communication between two equipments is normal . So I choose one as central...
I am using a nrf51822 based tag and Android official SDK to implement my custom app. I perform the following steps:
1. Scan
2. Connect
3. Discover services
4. Write...
What CRC type is used for the crc calculation with the function
uint16_t crc16_compute (const uint8_t * p_data, uint32_t size, const uint16_t * p_crc )
of the nRf52 SDK...
Hi
I have a prototype of a board that uses a nNF52832 to communicate over Bluetooth, the board has some buttons intended for user input.
As the board size is little...
Hello!
I am sorry to ask a simple question that why my device can't program the ".hex" file about the demo of ble_app_hrs_rscs_relay_s130_pca10028 after I have already program...
Hi,
I have Wifi MCU connected to nr51822.
I download the binary file from a Cloud and need to transfer it via UART, so i need a C code of the nRF5x Programing tool....
