Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I've recently began experimenting with the HID service and connecting to iOS devices in order to achieve lower connection intervals with Apple products (as described in their...
We have the Nordic nRF54L15-DK PCA10156 0.9.3 2025.19
We use nRF Connect for Desktop v5.2.1 and Programmer v4.7.2 and connect by USB to our ASI_nRF54L_DK1 001057739416....
Does Nordic have any libraries or solutions for negotiating with a USB C charger and requesting 9VDC for example? Or do you recommend that I use a separate dedicated ASIC...
nrf5340 NCS 3.1.0
Hello, I am trying to improve boot time and here are some spikes and timings. What I have found out is that CryptoCell init (hw_cc3xx_init_internal) takes...
Dear Nordic Team,
I'm currently working on an application that uses ACL and ISO to transmit data between 2 devices. ACL is used for transmitting operations that are then...
Hello,
I am developing using nrf5340 and optimizing the Bluetooth throughput currently.
Although experiments go well, there are a few things I would like to know more...
Recently, I've been evaluating the I2S interface of the 52840 to read ADC data from the TLV320ADC6140 chip.
The TLV320ADC6140 datasheet states that the chip supports TDM...
Hello everyone,
I’m a student currently working on a university project related to BLE-based positioning using the nRF54L15 and Channel Sounding .
In the documentation...
Zephyr board: nrf54l15dk_nrf54l15_cpuapp
Hi, we have a custom SPI NAND flash driver and are trying to create an external flash partition for our littlefs file system.
...
I'm very new to Zephyr so please be patient with me. I'm looking for an example that show me UARTs running on the following pins and setup. I have the echo_bot working with...
Hi
There is a github repo https://github.com/nrfconnect/Asset-Tracker-Template/tree/main that receives updates as of yesterday.
However on the documentation website...
I'm trying to get a previously fully functioning MQTT connection back up and running after some hardware difficulties, but am failing to get it to connect to the MQTT broker...
Looking for an example to adapt into my program.
I detect 'smp_svr' but compiling it give me error, it seems I need a flash configuration in file pm_static.yml, but I have...
Dear Nordic Support Team,
We are currently developing a new product utilizing the nRF9160 LTE-M module.
We are in the process of acquiring CE certification for our end...
Hi,
I have been facing issues with the configuration of the nRF9151 for sending and receiving UDP packets via the Skylo NTN network.
I am running firmware version:
...
Hello, on my nrf54l10 I observed a pin (GPIO 1.03) being actively driven low for ~20 ms during a reboot (e.g. Resetting after SystemOff Mode). I need this pin to stay high...
