I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi,I have a problem.Sometimes the program will execute to 0x08c8 during simulation on NRF52832，SDK15.2.0，Mesh3.2.I checked the map file, which is part of Softdevice.So I think...
Hello
Using PCA10040 dev board,
Building with SDK 16, & S112 - using ses
Running ..\examples\dfu\secure_bootloader\pca10040_uart_debug
Using nrfutil to download...
When running the "nrfjprog --recover --log" command, on a Windows 10 pc in CMD, this is the output that I get. I am unsure what steps I need to take from here.
Any help...
Hi,
In my application I have a requirement to send notifications to mobile on triggering particular Interrupts as well as particular events.I have created a customised notification...
Supported tx_power values: -40dBm, -20dBm, -16dBm, -12dBm, -8dBm, -4dBm, 0dBm, +3dBm and +4dBm.
What is difference in the behavior of nrf 52832 chip for these different...
We're developing Bluetooth tags that we would like to operate at both 1Mbps and coded (long range). From what I've read and seen from the Nordic testing, specifically "Testing...
I modified the gpio interrupt on the asset_tracker example of ncs v1.2, modified the following, and the interrupt didn't work: Where is available should be modified.
I set...
Dear Friend，
Based on nRF52832, mesh3.1, port ble dfu to mesh project, Android dfu application is based 'no.nordicsemi.android:dfu:1.10.1'; Call the following program: ...
My setup: custom board using nRF52840, Segger Embedded Studio 3.52, nRF5_SDK_for_Thread_and_Zigbee_v4
I used a couple of your projects as a starting point for my code. Specifically...
Hi,
In my proejct, I am using WFE(); in some while loops because of core low power mode.
For example, waiting for time_out flags like codes below.
I am wondering if...
Hi All,
I'm new to the nordic product. We previous using TIcc2642 as development board. And we would like to test our application over different hardware. Is there any...
Im using CUstom BLE tutorial example and it works fine. But i just wanted to know, in which section is the text data for logging occuring. Ex: "notfication received from ...
Hi community !
I want to know if a code works on nRF52840 DK PCA10056 will work on nRF52840 PCA10059 ? On both, i will never use physical input (button led or gpio) i'm...
Hello expert,
I just jump from TI. Could anyone tell me if nordic has any chipset like TI CC1310 which supports direct access to the receiver I/Q quadrature samples?
...
