Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I need to burst write the DMP library into the mpu6050 but not succeed.
The following is the function that I've been using to burst write.
I have researched on the...
Hi,
We developed our device with KEIL 5, SDK15.2 and SoftDevice 6.1.1. After we upgrade the SDK on our device from version 14 to 15, our IOS phone encountered the following...
Dears:
I'm testing the USB mass storage example: \examples\peripheral\usbd_msc with Nrf52840DK and SDK v15.3.0.
Now I have one question. When I plug in/out USB to PC or...
Hi
I am using the NRF52832 ,my code is based on the ble_app_hrs_freertos example sdk 15.0.0
I have one main task which usually run 64 time every second using the vTaskDelayUntil...
Hi I have a module that is used in a hand held instrument. It contains the nrf52832. It connects to phones for data communications. Is it possible to determine the strength...
Dear All,
I am trying to compile and run the ncs/zephyr/samples/drivers on the nrf9160_pca10090ns. For this reason, I have copy-pasted the file under the ncs/nrf/samples...
Sorry, I want to ask that if I can send Decimal(like accel x,gyro x) by the ble characteristic to the nrfConnect, when I send the information, it always becomes hexadecim...
Dear community members
I have end nodes with nrf52832 (Soft device s132) that can communicate to a central nrf52832 DK in Connection mode based on ble app uart and multiple...
hello, I'm develop use nRF52 SDK15.3 template to measure water press, and gyro value.
but in nrftoolbox app just show signed value, so i want to show signed value.
please...
Hello ,every one ,I found that the nrf Connect will disconnect it self after connecting to the device after 30 seconds, I'm using the sdk15.3.0 ble_app_template example,I...
NRF5_SDK_15.2.0
I am run my android code on android 9 and android 7. Unfortunately my android 9 is paired sometimes and not paired sometimes. especial after i tried to connect...
I am currently developing applications using nRFtoolbox. In case of ses, we are developing a template, but the application does not produce a negative value. In this case...
Hi, this is my first time using nRF52832 as a central device. (S132 6.0.0)
I set up the scan timeout parameters, it does stop scanning at the time I expect,
but strangely...
Hi,
It seems I'm running into the fairly common "solution load command failed (1)" error on a nRF42840DK board.
The console output in Segger gives me the following:
...
