Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
Hey
I am working for the first time on qualification process with SIG, my device is nrf51822 and softdevice - S130 (version 2.0.2) and I understand that D030168 / QDID-80592...
I am currently using bluetooth mesh v2.1 which has qdid code QDID: 111537 , now we are currently added the Nodic uart service code, do i also have to declare the QDID 138862...
Hi, I want to create a peripheral device with a nRF52810 module.
Before developing the corresponding mobile app, I would like to use this as a central device: A GUI, written...
I have been trying to get a arduino UNO and arduino Leonardo to communicate with the nRF9160DK but have not been able. That accounts for the SPI example aswell as the I2C...
Given that Zephyr RTOS is not certified for use on Medical Devices, is there any plan to support operating systems with FDA 510(k), IEC 62304, IEC 60601 certifications?
...
I'm looking at augmenting the GPS system of the nRF9160 (at the moment due to high current and long time to acquire, easily lost sats/location) with some geolocation. Specifically...
I met a question here. Hope anybody can help on it, thanks.
I'm evaluating whether it is feasible to run the FFT algorithm on zephyr LTS project, with the nRF52832 board...
I want to know the upgradation process of firmware (Zephyr OS) on nordic nrf52840_pca10056. I have flashed the Zephyr OS on chip once via Jlink/JTAG, and now I want to flash...
Hello,
We are developing a product which includes qr code reading as its feature.with reference to https://github.com/NordicPlayground/nrf52-ble-image-transfer-demo
as...
Dear All,
I need to develop a low-power application that sends a UDP message, waits for a certain amount of time (5 seconds) for a response and if there is no response it...
Hi,
Scenario : Scanning non mesh BLE packet with different stacks.
H/W Device - nRF52DK
Observation :
Case 1. Non Mesh BLE Stack (Soft device):: Here able to receive...
I'm working nrf52 DK, SDK V15.3 , S132 . I have created custom Services and characteristics its working fine. I need to change gap parameter in some cases because i need to...
Dear,
THINGY:91 / nRF91 DK
Currently, Power Saving Mode (PSM) is a feature that is not always available with roaming cards, and we must use the local sim card to use GPS...
