Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using nrf connect app on ios , the device is getitng on device mode but it is not showing DFU button on it , but it is working when using android app of it
And...
I want to generate a custom delay of one microsecond without using any timers By simply Executing instructions I want to generate. is there any possibility please let me know...
I have a rather strange issue.
I developed an application on the nrf52832 which amongst other, communicates with an ST Micro accelerometer LIS2DE12. The application works...
Hello,
Library seems to have limitation to 1kB. I'am talking about deffered mode.
You can increase NRF_LOG_DEFERRED_BUFSIZE >1kB, but it will crash if you try to print...
Hello, I am new to developing with nrf and have been trying to follow tutorials on individually setting pins as output. I am working on just getting a specified pin to blink...
Hi everyone,
Recently, I downloaded the SEGGER Embedded Studio, release 4.18, and start the development of a Heart Rate Monitor using nRF51422 and SDK 10 (softdevice s310...
I am only able to successfully trigger the ACK payload interrupt on the nRF24L01+ if I mismatch the payload lengths on the two devices; 4 for the nRF24L01+ and 1 for the nRF52840...
Hi everybody,
Intro facts :
I'm migrating from SDK 13.2.0 through SDK 14.2 to SDK 15.3.0. My program build on SDK14.2 but my product didn't work as expected, then I...
I need the P9 connector pinout (or complete schematic of Thingy:52 ) for programming my Nordic Thingy:52 using SWD. I have found this topics:
https://devzone.nordicsemi...
Hello, according to your website, nRF24 Series family is not recommended for new designs... as substitution you recommend to use nRF52 Series family. Can I ask you for the...
Aim: interface nrf32852 with i.MX6UL based Linux board through UART and configure hci of bluez. Board: nrf52_pca10040 SOM : nRf32852 OS: Zephyr UART: we followed HCI_UART...
Dear Nordic Team,
We are developing a custom board with nRF9160 with application of tracting device.
I am new user to this module and designing our device with target...
Hello,
I'm searching every where but i can't find what i want. Actually, i'm using two device and i really need to synchronise the execution of a process on both of them...
Hi All,
I have a problem to enable notification on my Android phone, i followed the tutorial on android web page (section bluetooth low energy) but my app crash, i have...
I understood how external board programming works with nrf52840 DK.
Debug IN (P18) is used for external debugger while Debug OUT (P19) supports external board programming...
