I am getting following error:
Error in final launch sequence
Error executing step execute method: stepInitializeJTAGFinalLaunchSequence
java.lang.reflect.InvocationTargetException...
Dear Nordic people,
I am playing (6.0.0) with sd_flash_page_erase() and sd_flash_write() , seems to be working ok, Allways happens what I do expect, but I am not able to...
Hi,
Will PAN item #56 TWI: TWI module lock-up be fixed in the Rev 3 version of the nRF51822/51422?
Also would you happen to have a time frame as to when the Rev 3 will...
Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
Hi,
I want to load both "SPM" and "http_update_ota" code separately to the nRF9160.
For that as suggested in " http://developer.nordicsemi.com/nRF_Connect_SDK/doc/0.4...
I've been trying to configure a second UART for use on the nRF9160 DK. However, I'm having some issues getting anything to send over the UART. I feel like I'm missing something...
Hi,
I use the nrfx_rtc_tick_enable() function to enable tick interrupts for the RTC.
I have a statemachine that in some states disable the interrupt and sometime enables...
Hi everyone !
I want to use serial communication with my ble project. So i tried to implement "/example/peripheral/serial " project into my ble project. I encountered too...
im using Feather EVM. im using the app_ble_uart . after i added SPI to the project i dont get any errors but the code does not run (goes to main) and when i press run it goes...
With an Objective to test mulitple DUTs that provides BLE4.2 data, We are in process of procuring the nRF52840 Dongle.
I would like to understand if i will be able to do...
I successfully installed the NRF9160 DK toolchain on my linux desktop the other day using the "Getting Started Assistant" App, but when attempting to install the same toolchain...
Hi!
I'm currently evaluating Thread using a few nRF52840 DKs.
The network will be used to gather and provide sensor values.
For various reasons, I want to avoid using...
Dear all,
I have two nRF52 Preview DK boards with the SoC nRF52840. I am testing the light switch example on both boards. I have changed the light_switch_server, such that...
I tried some steps and falling back to support. I received my custom nRF52832 board and wanted to kickoff programming the board to meet my requirements. I used nRF52840 DK...
Okay, this is a fairly involved issue, so I will try to simplify as best as I can.
In short, my new Ipad Mini 5 cannot connect to an NRF52840 running the NUS peripheral...
I have just purchased 2 pcs. nRF52840 - one of them works fine - the other one reports this when i run dmesg on my linux (tested on 2 different systems) "Cannot enable. Maybe...
Hi,
I'm using nRF52832-CIAA.
VDD,Pin A7, tide with Cap 4.7uF 0603
VDD Pin H7 tide with Cap 100nF 0201
DEC3 100pF 0201
DEC2 100pF 0201
DEC4 1uF 0402
Using LDO...
